Range 8 Kg/cm2, alarm to be set at 2Kg/cm2, at wat pressure reciever switch to

Range 8 Kg/cm2, alarm to be set at 2Kg/cm2, at wat pressure
reciever switch to be calibrated? justify the ans?

Question Posted / infantbesky

3 Answers
8503 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Range 8 Kg/cm2, alarm to be set at 2Kg/cm2, at wat pressure reciever switch to be calibrated? just..

Answer / shan

we are to calibrate at the pressure switch. Pressure switch
is the pressure reciever.we have to set the pressure switch
at 2Kg/cm2. If pressure reaches 2Kg/cm2,it will alarm.

Is This Answer Correct ?

12 Yes

1 No

Range 8 Kg/cm2, alarm to be set at 2Kg/cm2, at wat pressure reciever switch to be calibrated? just..

Answer / mithilesh kumar

1st pr. switch is combination of NO,NC,COMMON.OK.
for setting alarm at 2kg/cm2.
it calibrate with DEAD WEIGHT TESTER at 2kg/cm2.during
calibration NC becomes NO and NO become NC.it check with
multimeter in continuity mode.ok.
if it's done then your calibration is ok.
then you can use as per requirement.
any comment.
most welcome

Is This Answer Correct ?

3 Yes

2 No

Range 8 Kg/cm2, alarm to be set at 2Kg/cm2, at wat pressure reciever switch to be calibrated? just..

Answer / welcome4ujd

if range is 0 to 8 kg/cm2, an d alarm needed is 2 kg/cm2.
that is 25 percent of range, set the alarm at 6 psi of a 3
to 15 psi out put.
and if it is a flow transmitter of some range,say 0 to
1000 mmwc and alarm at 250 mm
then 25 % of flow in transmitter will give square root 25
devided by 10 tht is 50 percent in the control room , so
you have to set 50percent in the receiver switch that is 9
psi for a 3 to 15 psi out put.for basic flow transmitter
to find out square rooting from field to ccr
just square root the input percentage and devide by 10
to find the field input from control room signal
devide the ccr signal percentage by 10 and square it.

Is This Answer Correct ?

2 Yes

7 No

Post New Answer

More Instrumentation Interview Questions

Sir , i have completed my M.Sc In Instrumentation and presently working in Maintenance department 3 yrs Exp , is there is any possible for work in offshore ..

0 Answers

As you are fresher in Instrumentation & control engineer.Then why should I select you?

1 Answers

What is impulse line size

3 Answers IFFCO,

what is commisioning procedure,2)what is is the main work in commisioning in the field tx to dcs, plz send me detail

0 Answers

we are having yokogawa centum cs3000 dcs in our power plant. i need some of the operator guides NOT to appear in HIS0163 AND HIS 0162 but it shoul appear in HIS0164 HOW TO DO IT?

0 Answers Yokogawa,

admittance level sensor meaning?

2 Answers CGL,

in split range control system we are using two control valves,but we have only one positioner and one feed back link.so how we use this one feed back link for two control valves?

2 Answers

what is differences between singal acting and double action valve

1 Answers Carlo Gavazzi, Welspun,

Where do we consider the pressure in mbar & where do we consider the pressure in bar & why is it so ?

2 Answers BOC, Jindal Steel and Power,

What is input and output of plc & dcs

2 Answers

where proximity sensor installed on tank in loading arm application

0 Answers

I am working in a process industry, in that there are several sections devided in the SCADA screens and individual sections may START independently. But sometimes i am facing problem i.e, if section 2 Stopped by the operator immediately Section 1 or Section 3 or Section 4 is getting stopped can you expain the reason behind this?

5 Answers

For more Instrumentation Interview Questions Click Here