Answer / anu

nozzel is a device which convert (high pressure and low
velocity fluid) at inlet into (high velocity fluid and low
pressure) at exit

Answer / gaurav sharma

nozzle is the device which is used for converting fluids
pressure energy into kinetic energy. if a fluid is passed
through a tapered pipe its velocity is higher at the outlet
as compared to inlet

Answer / shrish

Nozzle work on two principal :
1. Countinuty Equation
2. Bernoulli's Principal
So if Area of Crossection decrease then velocity will
increase i.e. velocity head increases that will affect on
pressure head.
Means velocity increases & pressure decreases at outlet.

Answer / karthick

the function of the nozzle is to convert heat energy into
kinetic energy.the inlet velocity will bw minimum but
pressure will be high whereas the exit velocity will be
maximum and pressure will be minimum.the nozzle consists of
three sections convergent ,divergent and throat.the fluid
attains velocity less than sonic in convergent and sonic
velocity (i.e., mach no=1) in throat and supersonic
velocity in divergent section.

Answer / amit bhopale

Nozzle is a taper tube which drop pressure at inlet and
increase velocity at outlet

Answer / mani kandan

Nozzle which is used convert a pressure energy to kinetic energy

Answer / sandeep kumar

nozzle is used where we have high pressure and low velocity or k.e.but we needs low pressure and high velocity.
nozzle are generally of two kinds 1.CONVERGENT 2.DIVERGENT.
the nozzle whose inlet dia is greater and outlet dia is smaller is known as convergent while the nozzle who has low dia at inlet and large dia at outlet is known as divergent type nozzle.
WHEN WE PASS THE FLUID THROUGH A NOZZLE,ITS PRESSURE DECREASES AND VELOCITY INCREASES.
INLET VELOCITY <<<<< OUTLET VELOCITY
INLET PRESSURE >>>>> OUTLET PRESSURE

Answer / gatish mittal

the basic funtion of pressure nozzles is to convert the
pressure energy supplied by the high pressure pump into
kinetic energy in form of a thin film, the stabily of which
is determined by the properties of the liquid. such as
vescosity, surface tension, density and quality per unit of
time, and by the medium into which the liquid is sprayed.
the inlet pressure of pipe is more than outer pressure and
velocity is less than the outer velocity.
the velocity of nozzle is depends upon the ending point
diameter of nozzle, when a ending point of diameter of
nozzle is less than the velocity of fluid is more.

Answer / kundan kumar

It is a steady-flow energy transformation device which has varying Cross-section & it transform "high pressure energy { in form of heat energy } into high kinetic energy {high velocity }

Answer / ali

the importance of a venturi meter in the flow measurement system

Can we use pure oxygen in IC engines instead of air?? what would be the advantages and disadvantages of using it?? Have any steps been taken about this??

1 Answers  

the specific work input during a compression cycle from p1 to p2 , if compresion is isothermal, is given by p1v1logp2/p1. explain?

1 Answers  

What is the purpose of stern tube?

0 Answers   RRB,

I M POWER ENGG STUDENT FRM JADAVPUR UNIVERSITY CAN I GIV PSU EXAM 4 NTPC WHAT WOULD B THR PROCEDURE

3 Answers   NTPC,

Explain the nuclear reactor.

0 Answers  

What would happen if there was water in refrigeration line?

2 Answers   RRB,

What is the relationship between hardness and tensile strength?

0 Answers  

how works optical pyrometer ?

1 Answers  

what is the unit of force in C.G.S system and F.P.S system?

1 Answers  

What is the difference between an isometric and an orthographic drawing?

1 Answers  

What Happens when oil pressure in a dg set come down to zero.What are the trouble shooting methods?

1 Answers  

The stage below saturation is called?

5 Answers   TCE,