hw to find transformer is in normal position? whether its in charged condition

Categories >> Engineering >> Electrical Engineering
Suggest New Category

hw to find transformer is in normal position? whether its
in charged condition or not? except humming sound?

Question Posted / snr3032

9 Answers
14205 Views
ABB, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / vikrant gokul labhane

1)by sensetion (vibration ) of transformer .
2)by sensing the temperature of transformer.

Is This Answer Correct ?

9 Yes

0 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / vinothbabu.k

1.BY SENSEING THE VIBRATION IN TRANSFORMER.
2.BY SEEING SOME INDICATION LAMP R,Y,B IS IN CHARGE R NOT
IN TRANSFORMER.
3.BY SEEING THE RTC PANEL BOARD.
4.BY SEEING OIL TEMP INDICATOR(ITS NOT CORRECT BUT IT
POSSIBLE)

Is This Answer Correct ?

2 Yes

0 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / saroj kanta nayak

During Normal operation of tranformers,you should check
both winding as well as oil temperature which should be
below the maximum rated and check the breather condition it
should be blue than pink. And there should not be any
leakage of transformer oil on its reflectors.

Is This Answer Correct ?

1 Yes

0 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / prof ravi

If the transformer is working and if you go near the
transformer you can sense the heat generated by the
transformer even if no WTI or OTI installed on the
transformer.

Is This Answer Correct ?

1 Yes

0 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / bala123

Apart from Humming sound, we can found the following ways:-

1. OTI (Oil temperature indicator) shows the winding
temperature value
2.WTI (Winding temperature indicator)shows the winding
temperature value

but its not correct way because if we disconnect the TxR (after
some hours) charging both may show current values

Is This Answer Correct ?

1 Yes

1 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / akr

WTI OTI TEMP , DGA REPORT OF TRANSFORMER, TERMAL IMAGES BY
IRT

Is This Answer Correct ?

0 Yes

1 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / vivek

most probably we can use multimeter if the secondary value
is 415 v . if secondary values r high,surely there will be
voltmeter in the switchgear side for measuring the voltage.

Is This Answer Correct ?

0 Yes

1 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / sivaananth

Test the phase Wire use multimeter or anyother reading
meter.

Is This Answer Correct ?

0 Yes

3 No

hw to find transformer is in normal position? whether its in charged condition or not? except humm..

Answer / a

go n touch the fuse in LT side...if u get shock u can make
sure that it is charged.....

Is This Answer Correct ?

1 Yes

4 No

Post New Answer

More Electrical Engineering Interview Questions

What is voltage divider rule?

0 Answers

What is the safety of UPS?

0 Answers

how to find the ballast lost from the actual wattage? for example i am going to buy decorative type 2x36watts fluorescent light fitting for this lamp how to find the ballast lost? is there any formula?

2 Answers MEIL,

why neutral and body earthing of transformers kept separated? what is distance between two is required as per is?

6 Answers

How to calculate Temp from Resister from PT100 equation,

0 Answers

we have a lot of model of rectifier but thyristor rectifier is the most rectifier that use in power system. Do you know why this rectifier is used?

0 Answers

what is the difference between E.L.C.B & R.C.C.B?

2 Answers

How I design capacitor bank for different load.7MW connected load.

3 Answers Samtel,

why the transformer neutral give to the earth ?

2 Answers Jindal, JLL,

What kind of preventive maintenance are there for AC generator?

1 Answers Gulf,

Explain in brief description about the operation of DG sets.

0 Answers Siemens,

What will be the effect of in HT XLPE 220 KV cable when one side of the Armour/cable ends are not grounded. Will there is difference between 3-phase voltages? like: if A. Both End of Cable grounded Phase Voltages:- V1=219 KV, v2=220 Kv, v3=220 KV. B. One End is grounded other is not: than Impact on Phase Voltages:- V1= KV, v2= Kv, v3= KV. Remain same or unchanged??

3 Answers Jamshoro,

For more Electrical Engineering Interview Questions Click Here