Answer / saminder singh

Generating voltage of power station is generally considered
as 11 KV

Answer / sunny

generating voltage of power station is generally 11kv.

Answer / jijomon , maneesh , harikrishn

Generating Voltage of power station is 11,000volts

Answer / chintaman

Generating voltage of a power plant is depended on capacity
of power plant.If one power plant going to generate power
of 210 MW capacity then stator of generator gives 15.75 KV
output voltage.Then by step up transformer it increases
upto 220 kv for distribution.

Answer / gulshan goyal

GENERALY IT IS 11KV.BUT NOW A DAYS UPTO 23KV GENERATION IS
BEING DONE.IN INDIA IN NTPC DADRI IT ABOUT 16 KV FROM COAL
PLANT AND AROUND 12KV FROM GAS PLANT.IT MAINLY DEPENDS ON
THE CAPACITY AND TECHNOLOGY USED IN A PARTICULAR
PLANT.APPROXIMATELY RANGE OF GENERATING VOLTAGE IS 6.5-23
KV.

Answer / ashish rai

Mainly it depends on your technology , how much your
technology has been grown. In India max. voltage is 15.75
(NJPC). While other country like USA , Rusia , Canada are
too much away from this value.

Capacity of plant( power)

Answer / chetan & panks

Generating voltage of moreover Power Stations is considered
as 11 KV to 13KV.

Answer / neha

Generating Voltage is 11 KV

Answer / rajendra sadaphale

actually generated voltage is 11kv to 13.5 kv in india but
we can abale to increase that generated voltage but there
is a technical peoblem is that if generated voltage
increase size of generater also increase. also we required
modran technology. to improve it.

Answer / lekhraj signh

In india,generally generating Voltage is 11 KV

Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  

How do you know when the battery is fully charged?

6 Answers   ABB, Pricol,

what dose the arrow indicate in the symbol of power transformer?

1 Answers  

what is the different between surgearrester and lighting arrester

4 Answers   HPCL,

Why capacitor blocks DC current?

2 Answers  

What the reson for frequant instantaneous ground over current fault in our sync. Generator... 15 triping in 24 hr...

1 Answers   HCPL, Jhunjhunwala Vanaspati Jhoola, Regen Powertech,

what is the minimum bdv value for 400 kva transformer?

2 Answers  

If u take a kWh reading in 11 kV HT and 440 LV side at same time in yesterday today , then why LT consumed units 3-4℅ high as compared to HT units

1 Answers   Brigade,

What is PIR (pre inserting resistance) in 400kv EHV SF6 BREAKER? Why it use?

1 Answers   Adani,

How turns ratio test is done in three phase transformers?

2 Answers  

How many Zones can be in Conventional type fire alarm system & how can we detect the fire in Conv. type FAS?

0 Answers  

if single phase is having 220v supply then why three phase is having 440v instead of 660v?

4 Answers   C&S, NTPC,