Answer / parmar jignesh

EARTH POINT PLUG IS BIGGER , BECAUSE AS AREA IS MORE SO
RESISTANCE IS LESS & CURRENT WILL ALWAYS FOLLOW LOW
RESISTANCE PATH I.E WHEN ANY FOULT OR LEAKAGE CURRENT IS
THERE THEN IT WILL FLOW THROUGH EARTH POINT NOT THROUGH
PERSION OPERATING DEVICE, AS EARTH POINT RESISTANCE IS
LOWER THAN THE RESISTANCE OF PERSION OPERATING OPERATING
DEVICE

Answer / minal

we Know that,
Resistance= resistivityx length/area
This means that more the area ,less will be the resistance.
Also, resistance= voltage/current
since the resistance is high, more leakage/fault current
will flow through this big earth point.
Tha tis why, the size of earth hole is bigger than phase
and neutral.

Answer / chetan jain

The size of hole of the earth point in the plug point
bigger than the phase and neutral because , the earth point
is dirctly connected to the body of the electrical
equipment it makes the circuit completed before the phase
and neutral point's are connected, if there is a short
circuit happens it dirctly connects the equipment and
protects man for unwanted shock , or we can also say that
the earth point gives the path to the current to discharge.

Answer / a

during earth fault, high earth leakage current flows through
the earth terminal. so that hole is big

Answer / gtmanikandan

in my point of view
the flow of leakage current depend on the path the
resitance ,if it is resistance is less, cross section of
the conductor high,so we are normally provid less
resistance meterials that why the size of the conductor dnd
hole of the earth point are high

Answer / kk_london

I will give u simple example, the tank containing water
with small tap and the other tank with same capacity of
tank and water with big tap. If we open the taps at the
same time the tank with the bigger tap will drain out first
same logic applies to size of hole of the earth point in
the plug.

Answer / jetho balani

Technically there is no significant reason for having bigger earth point, but psychologically bigger indicate its more importance. As the bodyguard is useful when he is made stronger than the person for whom he is hired to guard, so all are advised not to avoid the use of earth point in order to safeguard yourself

Which cable is use for rtcc control panel

0 Answers  

"What is the difference between voltage and potential differnce?"

15 Answers  

How much dc volt applied in cathodic protection system?

0 Answers  

I need the recommended size for a 3 phase transformer at 13.8 KV Primary and connected loads of 3000 kVA at 4200 volts and 2375 kVA @ 480 volts AC.

0 Answers   Duke Energy,

as a electrical student why should i hire you?

0 Answers   TCS,

what is electricity.

6 Answers   HP, L&T,

what is the principal of starting of a three phase induction motor.

2 Answers   Moser Baer,

The SFC of an engine is 0.25 kg/kW hr. when the fuel used has a calorific value of 36000 kJ/kg. the thermal efficiency of the engine is

0 Answers   Caterpillar,

Kindly give the brief explanations for checking 12.5 kvar 440V, 25 KVAR 440V, 12.5KVAR 690V, 25 KVAR 690V capacitors microfarad values. what is the microfarad values for the above four type of capacitors, and give the formula explanations briefly. I know F-50HZ, voltage, and capacitor.

1 Answers  

in parallel operation of power transformer why the distance between power transformer and capacitor bank feeder is necessary to know

0 Answers  

respetsed sir, i have applied for section engg and juniour engg for both chennai and tiruvunabthapur boards for electrical deportments . can u suggest what books i have to follow and and also from which sections they r going ask (i mean weightage and what topics i have to cover) for both se and je for both chennai and tiruvunanthapur boards.......

1 Answers  

It is advisable 2 use auto-transformer if transformation ratio is-a)110KV/11KV,b)230kv/110kv,c)110kv/66kv,d) 400kv/230kv

2 Answers