How will we know in which direction a liquid is flowing in
a pipe?
Answers were Sorted based on User's Feedback
Answer / jayaa
liquid always flow due to the density difference & not due
to the pressure difference.
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / neeraj kumar
we can heat the pipe (if possible) at certain location and
check the temperature on two sides of that point of heating
significantly far away and then the direction of fluid flow
would be in that direction where the temp. is higher.
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / rabik
it is not only due to pressure hesd nor the potential had NOr the kinetic head.
it depends on total energy of the fluid at the particular section.
always any flow can takes place from higher energy to lower energy only. so we must use bernouli equation to determine the direction of flow,
Is This Answer Correct ? | 1 Yes | 0 No |
Answer / e.sivababu
it is flow from high level to low level narmally
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / qwe
actually guys we r given a solid pipe
in vich water is flowing.
so we want to know the direction.
or we want to know which end is a high pressure
end..............
i have not got the ans yet
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / pkp
concepts of pitot tube manometers entropy etc are good in a controlled conditions but without disturbing the flow or destroying the pipe only two things come to my mind ie either
by touching the pipe difference in temp at two places(it will
decrease in direction of flow )or ultra sound imaging of the
liquid
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / pkp
concepts of pitot tube manometers entropy etc are good in a controlled conditions but without disturbing the flow or destroying the pipe only two things come to my mind ie either
by touching the pipe difference in temp at two places(it will
decrease in direction of flow )or ultra sound imaging of the
liquid
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / sonu singh
See whenever there is any motion , that motion is from higher energy to lower energy . This is also the case with fluid flowing through a pipe . But while flowing through there would be some losses like frictional losses. So net energy is reduced. So what we can do is that we can apply a bernaulli equation to know the flow as it represents the net energy or net head. Bernaulli requires pressure head and velocity head . So if the cross section of the pipe is same we can then the velociy head would be same and we can directly compare the pressure head and if cross section is different then we hav to calculate both pressure head and velociy head and also gravitaional head if needed. And then we can compare the total head and find that where ever the total head is less the flow is toward that side.
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / gaurav
connect a u-tube manometer to pipe.at high pressure side
mercury will drop.and as we know liquid flows from high
pressure to low pressure side,so direction will be known.
Is This Answer Correct ? | 0 Yes | 0 No |
Answer / babji
whatever the liquid flowing at any direction high head to low head and low head to high head but the pressure applied is only one head this high head or low head but liquid flowing the low pressure head confarm
Is This Answer Correct ? | 0 Yes | 0 No |
A simple problem involing in hoops stress. For sphere: M= [3/2]*p*V*[density of pressure vessel material/Maximum working stress it can tolerate] For Thin walled pressure walls: Hoops stress or stress in the radial direction =p*r/2t ?
0 Answers Bhel, JPMorgan Chase,
800A bus-coupler system
Bending moment diagram for the UDL is in what shape?
• If you had enough money to retire right now, would you?
how much fuel use for perfect average in motorbike ....
What is the difference between DIN statndard and DN standard for flanges & what does PN mean in DIN standard.
give an example whenu should initiative and took the lead.
good book for material science and catia v 5 high scope domin to make career
fan having rotational motion why
0 Answers TATA, Tata Steel Limited, Telco,
What are killed steels and what for these are used ?
) Shall be responsible for the inspection/ maintenance of all the yard Assets as per the Maintenance procedure and maintain/update the related records correctly
State the function of neck ring in centrifugal pump?