Where do we consider the pressure in mbar & where do we consider the pressure in bar & why is it so ?

Answers were Sorted based on User's Feedback



Where do we consider the pressure in mbar & where do we consider the pressure in bar & why i..

Answer / mugil

Where below atmospherics pressure or Vacuum pressure(Negative) is to be maintain in that case mbar is using.Because milli bar is using very low pressure application.

Where above atmospherics pr is available in this case Bar is maintain

Is This Answer Correct ?    2 Yes 0 No

Where do we consider the pressure in mbar & where do we consider the pressure in bar & why i..

Answer / samir

mBar and Bar are both pressure unit. As per our system pressure we used the desired unit range transmitter or switches. As example if we have to measure PA fan header pressure pressure it's range very low as 5-10 Kpa,eg; 50-100mabar. So here we can used a transmitter or switches in bar unit instead Bar.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Instrumentation Interview Questions

what is the function of 3 way manifold valve in a closed loop system?

1 Answers   Emerson,


WHY THE DEGREE OF VALVE PLUG AND VALVE SEAT IS SLIGTLY DIFFERENT I CONTROL VALVE TRIM DESIGN

0 Answers  


How to Calibrate Interface Level Troll in field

0 Answers  


what are the installation requirement is common to all flow meter when volumetric flow rate is being measured

1 Answers  


Can DP transmitter with orifice plate works on Beta ratio 0f 0.3 and differential pressure of 100 MMWC in liquid service application?

1 Answers  






in split range control system we are using two control valves,but we have only one positioner and one feed back link.so how we use this one feed back link for two control valves?

2 Answers  


WHAT IS A SYMPTOM OF FAULT WITH THE SPAN OF AN INSTRUMENT? 1)ZERO-POINT AND 100% ARE CORRECT BUT NOT A MID-RANGE. 2)ZERO-POINT IS CORRECT ,BUT 1005 INPUT IS NOT GIVING 100% OUTPUT. 3)LINEARITY PRBS. 4)1005 O/p IS CORRECT BUT ZEO POINT IS WRONG.

1 Answers   Reliance,


Why Current(Ampere) is chosen as Fundamental Quanties not Charge(coulomb) ?

3 Answers  


In the field and in the control room different power supplies if used How to handle the ground

1 Answers   ITC Infotech,


Hi, I'd like to know the purpose of MOS (maintenance override switch). At site, these switches are installed in a stanchion with the transmitter (connected to ESD). thank you.

3 Answers   Adani, Adani Wilmar,


what is the principal of coriolis mass flowmeter

1 Answers  


In dcs panel we are using diff type of modules ?what is module ? what is the use of modules ?diff type of module?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)