Question - Chemical Engineering Material - In crystal material, hexagonal crystal system could form 4-digit index in certain direction of solid. For [1(-1)0] direction in the hexagonal crystal systems of particular catalyst applied in fume removal of incinerator, what is the four-digit index for this direction? Hint : The transformation equations between the 3-digit [h’k’l’] and the 4-digit [hkil] indices are : h = (1/3) (2h’ – k’); i = - (h + k); k = (1/3) (2k’ – h’); l = l’. A. [(-1)100] B. [1(-1)00] C. [(-1)000] D. [00(-1)(-1)] E. [(-1)0(-1)0]
- 1 Answers
- 1714 Views
- I also Faced
- E-Mail Answers
Answer / kang chuen tat
Answer : h = (1/3) [ 2 - (-1) ] = 1; k = (1/3) ( - 2 - 1 ) = -1; i = - ( 1 - 1 ) = 0; l = i = 0. Solution is [1(-1)00]. Answer is B. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.
| Is This Answer Correct ? | 0 Yes | 0 No |
QUANTUM CHEMISTRY AND CHEMICAL ENGINEERING - EXAMPLE 31.1 : As an approximation, let v = Zc / 137 where v is the radial velocity for 1 s electron of an element, c is the speed of light, Z is the atomic number. For gold with Z = 79, find the radial velocity of its 1 s electron, in term of c and percentage of the speed of light. (b) As an approximation, let A x A = 1 - Z x Z / 18769 where A is the ratio of the relativistic and non-relativistic Bohr radius. Find the value of A.
what is difference between B.Tech. and B.E. in chemical engineering
CHEMICAL ENERGY BALANCE - EXAMPLE 11.1 : Please match the term A - E with the stated definition i - v. Terms : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. Definitions : i. (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely); ii. (moles of desired product formed) / (moles of undesired product formed); iii. (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature); iv. (moles of vapour) / (moles of vapour dry gas); v. (mass of vapour) / (mass of dry gas).
In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?
sir, kindly explain to me that how to calculate volume of torrispherical vessel which is used in pharma company ss reactor bottom dish volume. thank u.
name of the fraction at which benzene xylene and toulene is obtained during coal tar distillation
i am going to appear vedanta written test so plz can any body suggest me for this on madhu.5393@gmail.com
ELECTRICAL TECHNOLOGY - EXAMPLE 16.2 : In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?
Explain why is post-weld heat treatment (stress relieving) sometimes necessary for welded vessels?
Question 73 - (a) A dryer reduces the moisture content of 100 kg of a potato product from 80 % to 10 % moisture. Find the mass of the water removed in such drying process. (b) During the drying process, the air is cooled from 80°C to 71°C in passing through the dryer. If the latent heat of vaporization corresponding to a saturation temperature of 71°C is 2331 kJ / kg for water, find the heat energy required to evaporate the water only. (c) Assume potato enters at 24°C, which is also the ambient air temperature, and leaves at the same temperature as the exit air. The specific heat of potato is 3.43 kJ / (kg °C). Find the minimum heat energy required to raise the temperature of the potatoes. (d) 250 kg of steam at 70 kPa gauge is used to heat 49,800 cubic metre of air to 80°C, and the air is cooled to 71°C in passing through the dryer. If the latent heat of steam at 70 kPa gauge is 2283 kJ / kg, find the heat energy in steam. (e) Calculate the efficiency of the dryer based heat input and output, in drying air. Use the formula (Ti - To)/(Ti - Ta) where Ti is the inlet (high) air temperature into the dryer, To is the outlet air temperature from the dryer, and Ta is the ambient air temperature.
Input the Roll Number, Name and marks of a small section of 5 students. Display the marks database of these students in the following format. The "Roll Number" and "Name" fields are left justified with 15 columns, and 25 columns, respectively. The "Marks" field is right justified with 5 columns. Assume the marks are in multiples of 0.5 and are from 0 to 100. Display some spaces between each field appropriately. Roll Number 11001 11050 11081 11225 Y2367 Name FIRST NAME LAST NAME FIRSTNAME2 LASTNAME2 I1. I2. FIRSTNAME3 FIRSTNAME4 M1. LASTNAME4 FIRSTNAME5 MID LASTNAME5 Marks 95 80 88 77.5 89.5 The input can be stored in a file, say, marksdata.txt, and the program can be executed by using ./a.out < marksdata.txt
What are the advantages of using gear pumps?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
