explain about where should we use deep groove ball bearings,angular contact ball bearings,spherical roller bearings,taper roller bearings,cylindrical roller bearings and thrust bearings

0 Answers   Lanco, TATA,

---

I need BHEL apptitude questions

0 Answers   Bhel,

---

1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?

0 Answers   Bhel,

---

when do we use roller bearing, deep groove ball bearing, angular bearing, sealed bearing, semi sealed bearing, unsealed bearing, anti friction bearing, journal bearing, thrust bearing

0 Answers  

---

I got an interview call from CANARA BANK for the post of TECHNICAL MANAGER (MMG-II), Can any one tell me what are the questions will be asked?

0 Answers   Canara Bank,

---

---

why companies are using First and third angle projection? why not second and Fourth?

7 Answers   CADD,

---

we need tech specs of HP fan cap 50,000 m3/Hr, Pressure o.5-0.7 Bar for blast furnace at steel plant

0 Answers   Despro Technologies,

---

sir,kindly give brief knowledge about various welding processes like SMAW. GTAW,SAW ,and ASME ,IBR code at my i.d kyoor143@gmail.com

0 Answers   Reliance,

---

Poisons ratio is higher in (rubber/steel/wood)

5 Answers   Essar,

---

How do we calculate the CFT?

1 Answers  

---

i want to know the difference between proportional hydraulic valve & servo hydraulic valve

0 Answers  

---

what are the different theories of failure under static load, explain briefly?

0 Answers   Bechtel,

---