1. What are good characteristics of good combustion in a
boiler? 2. What do you analyze from boiler water analysis?
3. What do you treat in high alkalinity of boiler water? 4.
What is a feed water pump? Dearator feed heater? 5. What is
the purpose of the nozzle of impulse turbine? 6. What are
the things needed to have an efficient boiler burning? 7.
Name Of Parts And Each Purpose 8. What are the causes of
emergency stop in a steam engine? 9. What is the normal
vacuum pressure in a steam turbine atmospheric condenser?
What would cause the press to falls? 10. Steam turbine
(function an parts) 11. What is the boiling point of water?
12. What are the safety devices of boiler? 13. What is the
effect of high alkaline water to a boiler? 14. Steps In
starting boilers. 15. Small gear found in the steam turbine.
16. What is an Economizer? 17. What are the methods of heat
transfer? 18. Types of pressure 19. What are the different
parts of impulse reaction turbine? 20. What is the color of
the flame of the boiler running in good condition? 21. What
type of pump is commonly used is feed water system in
auxiliary boiler? 22. What is the specific heat of water?
23. What do you do to prevent flare black? 24. What is a
brake horsepower? 25. What is the purpose of a
de-superheater? 26. What is the purpose of corrugated
furnaces? 27. What are the causes of steam turbine failure?
28. What is the purpose of superheater? 29. Given a cutaway
isometric view of the steam turbine. Examinee was asked to
identify the following Parts: 30. What is thrust bearing?
31. Give five boiler mounting valves. 32. In steam boiler,
what are the various test in water boiler? 33. How much
calorific value of heat is needed to heat 00c of 34. What
will happen if boiler backfires? 35. What is the color of
flame if the boiler is running in good condition? How about
when it is not in good condition? 36. How does the steam
work in a steam turbine? 37. What are the causes of boiler
backfire and steps in how to prevent it from happening? 38.
What are the causes of high alkalinity in boiler water? 39.
What are sensible heat, latent heat, and specific heat of
water? 40. What are the causes of turbine vibration 41.
Identify the parts of steam turbine 42. What is the normal
Ph value of boiler water 43. Causes of dilution of
lubricating oil in a steam turbine? 44. Explain briefly-
good combustion of auxiliary boiler? 45. Method of testing
or checking boiler water? 46. What is mean carry over of
Aux. Boiler? 47. What are steam turbine parts usually come
into damage? 48. Why must we pay attention when we drain
steam in steam turbine. What factors are observed? 49. What
type of pump use in boiler F.O. system? 50. What parameters
to be reported when we send lubricating oil for shore
analysis? 51. In boiler, what does steam and smoke goes out
to the funnel. What reason? 52. Where can you find the feed
check valve and feed stop valve and give the purpose of it?
53. What are the causes of troubles in boiler during
operations? 54. Give the purpose of nozzle in impulse
turbine? 55. What s gland sealing steam? 56. How to prevent
back fire of boiler? 57. What is the used of economizer in
boiler? 58. What is the seal packing gland for turbine? 59.
What is the flow of steam in an impulse turbine? 60. What
will happen if you blow the soot in the boiler? 61. State
the purpose of air heater? 62. How to operate soot blower
boiler and economizer? 63. What do you mean by A.CC.? 64.
What is the thermal efficiency of a diesel engine? 65. What
is a blow down valves?


No Answer is Posted For this Question
Be the First to Post Answer

Post New Answer

More Mechanical Engineering Interview Questions

how i can calculte the lenght of a ring dia 27 mm.

5 Answers   TATA, WWE,


distinguish the knock phenomena of ci and si engine?

0 Answers  


What causes diesel engine to automatically stop?

0 Answers   RRB,


previous question papers for group 2

0 Answers  


What will happen when engine stays in critical speed of 58-65 RPM?

1 Answers  






What is the difference between Over Molding and insert molding ?

0 Answers  


What are the different types of pumps? and their usage.

0 Answers   John Deere,


What Equilibrium?

3 Answers   SVNIT,


ifferent between technology & engineering?

4 Answers  


What i the role of a turning gear attached to a shaft line of a steam turbine

2 Answers  


i want to know how a dg set run/works and what is strock and what difference in between two and four strock engine.

0 Answers  


which is heavier 1kg. of iron or 1kg. of cotton?and why?

33 Answers   Getco, Jindal, Lloyd, Naval Academy, NDA, samr, swiggy,


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)