Answer / manas

Density is a physical characteristic of material or substance.
The mass density or density of a material is defined as its
mass per unit volume.
So Density=M/V
Units of Density:-
The SI unit for density is:

kilograms per cubic metre (kg/m3)
kilograms per litre (kg/L)
grams per millilitre (g/mL)
metric tons per cubic metre (t/m3)

Answer / balu

Density:
Ratio of mass per unit volume. Used as a factor for
interconversion of mass and volume.

Thyristor related applications

1 Answers  

---

A cantilever beam of length L = 3 m carries a uniformly distributed load (UDL) of W = 20 N / m throughout the length. Calculate the bending moment, BM of the beam near the fixed end. What is the shear force, SF at this point? Let SF = -WL, BM = -LWL/2.

1 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.4 : The resolution of separation, Rs for chromatography is given by the formula Rs = (difference in retention time) / (average width at the base). In a chromatogram, 3 peaks a, b and c are found. Average widths W at the bases of the solutes are : Wa = 20 s, Wb = 40 s, Wc = 30 s. Resolutions of separation, Rs for solutes b and c in comparison to a are 2 and 4 respectively. The differences in retention times T for b and c in comparison to a are (Tb - Ta) and (Tc - Ta), Ta = Tc - Tb : (a) Form 2 equations involving Rs as a function of Wa, Wb, Wc, Ta, Tb and Tc. (b) Find the values of Ta, Tb and Tc.

1 Answers  

---

Explain how can one estimate how the friction factor changes in heat exchanger tubes with a change in temperature?

0 Answers  

---

PROCESS DESIGN - EXAMPLE 21.1 : According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.

1 Answers  

---

How can one estimate how the friction factor changes in heat exchanger tubes with a change in temperature?

0 Answers  

---

what is mass flow rate of steam of 7 kg/cm2 pressure in 1 inch id. pipe.

0 Answers   Ascent,

---

My previous company dismissed from my job due to some reason. But they have given 1 year experience certification. But i worked for 1 year 4 months, How do i answer if interviewer asked what did you do for six months.why are you leaving your job?

4 Answers  

---

plz send me hpcl and reliance entrance test papers on my id s,kumar_bk@yahoo.co.in

1 Answers   Reliance,

---

MASS TRANSFER - EXAMPLE 4.1 : A concentric, counter-current heat exchanger is used to cool lubricating oil. Water is used as the coolant. The mass flow rate of oil into the heat exchanger is 0.1 kg / s = FO. For oil, the inlet temperature TIO = 100 degree Celsius and the outlet temperature TOO = 55 degree Celsius. For water, the inlet temperature TIW = 35 degree Celsius and the outlet temperature TOW = 42 degree Celsius. What is the mass flow rate of water in kg / s, FW needed to maintain these operating conditions? Constant for heat capacity of oil is CO = 2131 J /(kg K) and for water is CW = 4178 J /(kg K). Use the equation (FO)(CO)(TIO ?TOO) = (FW)(CW)(TOW ?TIW).

1 Answers  

---

In a Furnace arch pressure is more than Hearth pressure,then how flue gas travels to stack

0 Answers  

---

Why does catalytic converter used in an automobile?

0 Answers  

---