why we use kg/cm2 instead of kg/m2 as a unit of pressure. As
we know kg is a MKS unit and cm is a CGS unit. So why we use
combination of both(kg/cm2)while describing the pressure.
- 3 Answers
- 9539 Views
- IES, NTPC, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / rajesh kumar shukla
when we are meauring the presure in kg/m2as a unit of
presure hen then there is great difference in the result of
the presure as comparethan kg/cm2 because the surface or
cross sectional area at which the presure is to measure
have greater percentage error in measuring the area. so we
use the kg/cm2.
| Is This Answer Correct ? | 26 Yes | 4 No |
Answer / abhi
Measurement of pressure in
kg/m2 will lead to lot of
complications due to powers
of 10.
| Is This Answer Correct ? | 0 Yes | 4 No |
Answer / pardeep
its eual to 1 atm thats why we used this.it ie to calculate
| Is This Answer Correct ? | 1 Yes | 9 No |
What is a slined joint?
In Turbine how the balence piston works and what is the direction of leak of steam flow.
Explain the formation of micro structures of pearlite, bainite and martensite in steel?
What is the purpose of starting air?
Where can you find the feed check valve and feed stop valve and give the purpose of it?
Name of the tables which is going to join two tables in querry ?
What is MVA, KVA, X-mer ?
Explain bearing
Is there anyone need material testing instrument?
suppose that there is a gas turbine of 110MW having 3 stages, and compressor having 17 stages. what will happend when the stages of turbine increses to 6.
how material removal occurs only in workpiece not in tool during an EDM process?
1. What are good characteristics of good combustion in a boiler? 2. What do you analyze from boiler water analysis? 3. What do you treat in high alkalinity of boiler water? 4. What is a feed water pump? Dearator feed heater? 5. What is the purpose of the nozzle of impulse turbine? 6. What are the things needed to have an efficient boiler burning? 7. Name Of Parts And Each Purpose 8. What are the causes of emergency stop in a steam engine? 9. What is the normal vacuum pressure in a steam turbine atmospheric condenser? What would cause the press to falls? 10. Steam turbine (function an parts) 11. What is the boiling point of water? 12. What are the safety devices of boiler? 13. What is the effect of high alkaline water to a boiler? 14. Steps In starting boilers. 15. Small gear found in the steam turbine. 16. What is an Economizer? 17. What are the methods of heat transfer? 18. Types of pressure 19. What are the different parts of impulse reaction turbine? 20. What is the color of the flame of the boiler running in good condition? 21. What type of pump is commonly used is feed water system in auxiliary boiler? 22. What is the specific heat of water? 23. What do you do to prevent flare black? 24. What is a brake horsepower? 25. What is the purpose of a de-superheater? 26. What is the purpose of corrugated furnaces? 27. What are the causes of steam turbine failure? 28. What is the purpose of superheater? 29. Given a cutaway isometric view of the steam turbine. Examinee was asked to identify the following Parts: 30. What is thrust bearing? 31. Give five boiler mounting valves. 32. In steam boiler, what are the various test in water boiler? 33. How much calorific value of heat is needed to heat 00c of 34. What will happen if boiler backfires? 35. What is the color of flame if the boiler is running in good condition? How about when it is not in good condition? 36. How does the steam work in a steam turbine? 37. What are the causes of boiler backfire and steps in how to prevent it from happening? 38. What are the causes of high alkalinity in boiler water? 39. What are sensible heat, latent heat, and specific heat of water? 40. What are the causes of turbine vibration 41. Identify the parts of steam turbine 42. What is the normal Ph value of boiler water 43. Causes of dilution of lubricating oil in a steam turbine? 44. Explain briefly- good combustion of auxiliary boiler? 45. Method of testing or checking boiler water? 46. What is mean carry over of Aux. Boiler? 47. What are steam turbine parts usually come into damage? 48. Why must we pay attention when we drain steam in steam turbine. What factors are observed? 49. What type of pump use in boiler F.O. system? 50. What parameters to be reported when we send lubricating oil for shore analysis? 51. In boiler, what does steam and smoke goes out to the funnel. What reason? 52. Where can you find the feed check valve and feed stop valve and give the purpose of it? 53. What are the causes of troubles in boiler during operations? 54. Give the purpose of nozzle in impulse turbine? 55. What s gland sealing steam? 56. How to prevent back fire of boiler? 57. What is the used of economizer in boiler? 58. What is the seal packing gland for turbine? 59. What is the flow of steam in an impulse turbine? 60. What will happen if you blow the soot in the boiler? 61. State the purpose of air heater? 62. How to operate soot blower boiler and economizer? 63. What do you mean by A.CC.? 64. What is the thermal efficiency of a diesel engine? 65. What is a blow down valves?
0 Answers CSPDCL-Chhattisgarh State Power Distribution Company Limited, RRB,
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
