what are the programming languages used in dcs
Answers were Sorted based on User's Feedback
Answer / minhaz mohtashim
1. Instruction list (IL)
2.Ladder Diagram (LD)
3. Functional Block diagram (FBD)
4. Sequential Functional Chart (SFC)
5. Structured Text (ST)
6. Continuous Function Chart (CFC)
| Is This Answer Correct ? | 56 Yes | 10 No |
Answer / eng. kamal elbsser
They are five : Ladder daigram ,function block daigram FBD,
structure text ST,Instruction list IL and finally
Sequential function daigram SFC .
| Is This Answer Correct ? | 20 Yes | 3 No |
Answer / sakthivel
ladder logic, statement list, functional block,and atill
more two is there ...
| Is This Answer Correct ? | 23 Yes | 11 No |
Answer / ali
only fbd is there 4 dcs and others r 4 plc,they are iec 61131 languages
| Is This Answer Correct ? | 4 Yes | 4 No |
Answer / dipen
FOR DCS THE PROGRAMMING LANGUAGE IS CL ( CONTROL LOGIC).
DCS PROGRAMMING AND COMMUNICATION IS BASED ON THIS CL. EACH AND EVERY SECTION HAS ITS OWN CL BASED ON PROCESS REQUIREMENTS.
| Is This Answer Correct ? | 3 Yes | 3 No |
Answer / abhijt n. sonar
In PLC the most frequently used language is Ladder. This is
available in almost all types of PLCs but beside of this
language there are other languages as follows...
* C language
* C++ language
* FBD
* Text
* etc... specially developed by Mfg. like Automation Basic
by B&R Mfg.
But finally all program is converted into Machine language
i.e. in Binary formates...
| Is This Answer Correct ? | 1 Yes | 13 No |
Answer / kumaran
i think most of the DCS writing C , C++ language
| Is This Answer Correct ? | 6 Yes | 37 No |
Define the difference between a stable versus an unstable controlled system and some of the tools you might use to be able to detect when this is happening and assumptions used for control system application design that could contribute to instability
Name four general (not technical) criteria that would you consider important, when deciding upon a particular control valve?
How to measure high frequency using thermistor
In Boiler Drum Level- Level control valve how can it tuning (PID)?
what are the difference between conventional and smart transmitter.
I have observed in field instrumentation work... I remove the fuse of an analog transmitter then it shows 7.75 kg/sq cm (which is practically wrong value)in DCS and when put the fuse it shows 0 in dcs. Then cheach the field transmitter termination and found moister. clean that and then it shows 1.1 kg/ sq cm which is right value. Please describe the above phenomenon.
How many interlocks at turbine side?
When a field input to plc is coming from 400 to 600 meters and the input is in 24 V DC? So signal cable of which cross section i should select for proper signal to plc?
How will you calibrate PID controller? explain with example.
0 Answers Jacobs, Sirte Oil Company,
what is the input of digital counter during the the calibration time?
Consider a control valve action,the inlet air pressure is only 6 ksc but physically how it can be operate against 100 ksc line fluid pressure?
how to calculate control valve bonnet size?? or how to select its material?
Civil Engineering (5086)
Mechanical Engineering (4456)
Electrical Engineering (16639)
Electronics Communications (3918)
Chemical Engineering (1095)
Aeronautical Engineering (239)
Bio Engineering (96)
Metallurgy (361)
Industrial Engineering (259)
Instrumentation (3014)
Automobile Engineering (332)
Mechatronics Engineering (97)
Marine Engineering (124)
Power Plant Engineering (172)
Textile Engineering (575)
Production Engineering (25)
Satellite Systems Engineering (106)
Engineering AllOther (1379)