LADDER LOGIC Can any body state Logic on following condition Instructions to u

LADDER LOGIC
Can any body state Logic on following condition
Instructions to use 1-XIC 2-XIO 3-Output ONLY
Program
Push 1st button On - 1st lamp should On
Then Push 1st button Off - 1st Lamp Should remain on
Push 2nd button On - 1st lamp should Off and 2nd lamp should On
Then Push 2nd button Off - 2nd Lamp Should remain on.

Question Posted / harshmakar

4 Answers
8449 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

LADDER LOGIC Can any body state Logic on following condition Instructions to use 1-XIC 2-XIO 3-Out..

Answer / gururaajan

In first rung use NO contact of Pushbutton 1 and latch it
with 1st lamp NO contact.Then use NC contact of 2nd button
and in output side use 1st lamp.In second rung use NO
contact of 2nd button latched with NO contact of 2nd lamp
and in output side use 2nd lamp.

Is This Answer Correct ?

3 Yes

0 No

LADDER LOGIC Can any body state Logic on following condition Instructions to use 1-XIC 2-XIO 3-Out..

Answer / manraj

no,
Push 1st button On - 1st lamp should On
Then Push 1st button Off - 1st Lamp Should remain on
Push 2nd button On - 1st lamp should Off and 2nd lamp
should On
Then Push 2nd button Off - 2nd Lamp Should remain on.
it should be by process.

Is This Answer Correct ?

3 Yes

1 No

LADDER LOGIC Can any body state Logic on following condition Instructions to use 1-XIC 2-XIO 3-Out..

Answer / mohammad wasim khan

rung1
xio (adress I:0/1) pb series 2 xic puch button in paralllel and give adress as(O:0/0) to one of xic pb and adress (I:0/0)to second xic , a output in series with adress O:0/0.

rung 2
xio (adress I:0/2) pb series 2 xic puch button in paralllel and give adress as(O:0/1) to one of xic pb and adress (I:0/1)to second xic and a output in series with adress O:0/1.

Is This Answer Correct ?

1 Yes

0 No

LADDER LOGIC Can any body state Logic on following condition Instructions to use 1-XIC 2-XIO 3-Out..

Answer / chandrasekarapandian

Yes it is possible with latch & Unlatch,

1 st rung NO switch 1 with latch coil(Lamp 1)
2 nd rung NO switch 2 with Unlatch coil (Lamp 1)
Parallel with
Latch coil (Lamp 2)

Is This Answer Correct ?

0 Yes

1 No

Post New Answer

More Instrumentation Interview Questions

What is ALSPA 370 control system

1 Answers DUBAL-Dubai Aluminium,

plz... clarify my answer, how to calibrate vaccum (DP)leveltransmitter,it is hart. (digital).DETAILS:(coloumn)closedtank height 2650mm,and tx range is 0-1500mmH20.

2 Answers KNPC,

Sir , i have completed my M.Sc In Instrumentation and presently working in Maintenance department 3 yrs Exp , is there is any possible for work in offshore ..

0 Answers

In your own words, would you expect an ultrasonic level device to work better in a pressure vessel with a high pressure or a strong vacuum, and why?

1 Answers

I am using 971 Enraf radar level transmitter for LPG tanks ,the tank side indicator gives the error code 999999999FL can any body give me any diagnostic for this issue?

0 Answers

what is remote mount with MTA option? (In case of Dual Sensor Vortex Flowmeter,rosemount has written in its catalog drawings).

2 Answers

If P will increase then what will happen with PID?

1 Answers Chettinad, Galfar, Mehran Sugar Mills,

It is desired to reduce effect of 50Hz pick up in a thermocouple measurement. If a third order LP filter is used for this, what should be its cut off frequency, if gain should be 0.001 at 50Hz.

1 Answers Honeywell,

what is DCS?

24 Answers Reliance, SWCC,

WHAT IS THE DIFFERENCE BETWEEN DCS & PLC.

9 Answers Reliance,

Is wet leg type system nessesary to measure water level of steam DRUM? How the transmitter is calibrated to measure this level?

0 Answers

What is the loop calibration? Which instrument used to loop calibration and how?

2 Answers Descon, QCon,

For more Instrumentation Interview Questions Click Here