Answer / prerit sarswat

First of all i want to comment on the answer of Meenakhsi,
please clear your concept then give the answer publicly.

UPS stands for Uninterruptible power supply.
As the name suggested ups is used to give the
Uninterruptible supply to computer even when any electrical
power cut occurs.
It consist of number of MOSFETs for converting dc supply to
ac supply from battery without any time delay.

Answer / meenakshi

ups will be present between the equipment and power socket.
the electricity flows from socket to ups n then to
computer, battery continuosly checks the power levels and
also collects the power.when the power levels are not
within the normal parameters, ups vil connect the batteries
for compensating the lack of power.whwn the power is
restored to the normal flow,ups vil start recharging the
batteries.

Answer / shekar

ups is an interupted power supply unit.
Main supply will be directly given to the load and also to
the rectifiers which converts AC to DC to charge the
battery.when mains fail the charged battery will flow to
the invertor which converts DC to AC and will flow to the
loads.

Answer / william lobo

UPS is uninterruptible power supply and is widely used by
one and all. It consists of battery backup and charging
facility. diagram can be supplied if you write to me at
williamloboatrediffmaildotcom.

Answer / loboreliance2003

The circuit drawn pertains to a regular industrial UPS
(Uninterruptible Power Supply), which shows how the
batteries take control during an outage in electrical
supply or variation beyond the normal limits of the voltage
line, without disruption on the operation providing a
steady regulated output (5 Volts by LM7805) and an
unregulated supply (12 Volts).

The input to the primary winding of the transformer (TR1)
is 240V. The secondary winding can be raised up to 15
Volts if the value is at least 12 Volts running 2 amp. The
fuse (FS1) acts as a mini circuit breaker for protection
against short circuits, or a defective battery cell in
fact. The presence of electricity will cause the LED 1 to
light. The light of LED will set off upon power outage and
the UPS battery will take over

The circuit was designed to offer more flexible pattern
wherein it can be customized by using different regulators
and batteries to produce regulated and unregulated
voltages. Utilizing two 12 Volt batteries in series and a
positive input 7815 regulator, can control a 15V supply.

If you want the diagram then contact me at
williamloboatrediffmaildotcom

Answer / meenakshi

well ppl,everyone knows the full form of ups and tat, it
provides the back up facility.but the question posted
is "what is the OPERATION OF UPS". frankly speakin even i
dint know the answer.i surfed the net n i went thru the
following link http://www.backuphowto.info/how-calculate-
ups-battery-backup n found the answer to be quite
satisfactory.if u still think the answer is wrong,i
apologise for tat....

Answer / ankit tyagi

This is uninterruptible power supply (UPS), is primarily
used to provide a backup power source to the parts in the
computer case, the monitor, and any other device plugged in
to the battery backup.UPS is mains function converts the DC
suppy to AC supply when flow the load .

What is referred to the electron in the outer orbit?

0 Answers  

what is the differnce between ac and dc?

5 Answers  

what is diffrent between plc and clc??

1 Answers  

from which formula we select a capacitor rating?

4 Answers   Suzlon,

What is cp system and why is it required.?

1 Answers   Essar,

one 60KVA UPS how can full load current tell me us formulas

1 Answers   Wipro,

A cable with concentric PE conductor must be used with frequency converter circuits what does its means.?

0 Answers  

what is resistor

9 Answers  

As per standard, transformer body earthing and other Equipment earthing (Equipment earthing) did not connect. but in LT side termination we are doing metal glanding in both side Transformer to PCC Panel through armoured cable, now X'mer body earthing and PCC Pane earthing (Equipment earthing) both are connect.is this safe for X'mer or other equipment?

0 Answers  

Can we pass 11kv power in 1.1kV voltage grade cable.If not why?.

3 Answers  

According to general circuit diagram of 1-Phase t/f , why the primary is not get short circuited ,even though the supply terminals both are directly connected through primary winding?

4 Answers  

what is the diffrantial relay???????why we use it on the MDB

5 Answers