Answer / haribalakrishnan

For Example if we take 110v Battery bank...Normally in
commissioning time we will put in Boost charge mode in
charger to charge the battery bank, that means we have
charge the battery upto the specified limit given by the
manufacturer,for 30hrs duration.The voltage is around
154v...after that it will come to float mode it maintain
the constant voltage 115V..Normally batteries are in
floating mode only..Only at the time of Initial charging
and if suppose batteries are drained then only we put it in
Boost charge mode....

Answer / subramannian kp

Boosting Charger means charging of battery when it is fully
discharged. On this charging, per cell voltage will be
high resulting the system voltage to be a high value. So it
should have to provide a designed voltage to the load so
the load is connecting through avoiding certain number of
cell where and which it is known as Tapcell.
Floating Charger or Trickling Charger means the fully
charged battery in which we have to keep the voltage in a
particular limited range so tends to goes the voltage down
that due to leakage or a little consumption by applying a
little value of charging current.

Answer / pillay

We use a charger in float charger mode
when the battery is already fully charged,
but charging is still necessary to take
care of the losses within the batteries
and the current it is supplying.
we choose booster mode when the battery
is still under charged or the load current
is too high the float charge mode current
cannot cope with the load and the battery
eventually gets discharged.

Answer / ram

Floating Charger means the fully
charged battery in which we have to keep the voltage in a
particular limited range so tends to goes the voltage down
that due to leakage or a little consumption by applying a
little value of charging current.
booster charger means charging of battery when it is fully
discharged. On this charging, per cell voltage will be
high resulting the system voltage to be a high value. So it
should have to provide a designed voltage to the load so
the load is connecting through avoiding certain number of
cell where and which it is known as Tap-cell.

why we use ac as a electric appliance in home or daily use?

1 Answers   MNC,

---

What is the fuction of UV & how it works in circut breakers? is it one type of relay?

4 Answers  

---

working of a diesel generator.

34 Answers   ABC, AC, Cognizant, CTS, Directorate of Lighthouses and Lightships, KSL, Quippo, Shree Renuka Sugars, SRF, Svam Power, Tech Mahindra,

---

What is MS-EXCELL?

0 Answers   NTPC, Siemens,

---

What is principle of Floroscent tube 36watt.

0 Answers   Diamiller, NDPL, Trident Hilton,

---

how to calculate circuit breaker capacity

6 Answers   Siemens,

---

why a fan starts rotating in the reverse direction when condenser gets damaged?

1 Answers  

---

a)In a 3-phase 4-wire circuit, a circuit breaker is selected to protect the circuit whose highest fault level is 6.6 MVA. Determine the required minimum breaking capacity in kA. (Note: Covert 3-phase power in terms of kA to find answer.) b)Using the below, determine the required minimum making capacity in kA as a “peak value”. Rate breaking capacity (Icn) ka: Icn<= 1.5 Factor = 1.41 1.5

0 Answers  

---

What is servo motor? what is its purpose?

0 Answers  

---

In a incandescent bulb, if the glass is punctured, and then power is supplied, the tungsten filament blows up with a flash.Why?

2 Answers  

---

what is the diffrence between earth and neutral.

1 Answers  

---

Why should not we run the IM in low voltage, if runs means what will happen?(for example instead of 400V we give 250V supply)

2 Answers  

---