Interested to Buy Any Domain ? << Click Here >> for more details...
Why we use vestigial side band (VSB-C3F) transmission for
picture?
- 16 Answers
- 69566 Views
- BPL, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / niharika
bandwidth of signals used for picture reception is very
large,so standard AM cannot be used.if ssb were used,it
would result in half the bandwidth and ssb receivers being
complex,they are not used.so vestigial transmission is used
in which a vestige or trace of the unwanted sideband is
transmitted along with the wanted sideband and carrier.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / ishita sharma
In a TV receiver, phase response of the filter near the flat
passband would have harmful effect on the received TV
signal, a portion af unwanted sideband must also be
transmitted,as it acts like a guard band.
| Is This Answer Correct ? | 9 Yes | 10 No |
Answer / nagaraj hegde
As our ear is not sensitive to phase distortion..so ssb can be used for to transmit the speech signal..but for picture phase distortion is more noisy so it cannot be used ...thats why vsb is used ..
| Is This Answer Correct ? | 1 Yes | 2 No |
Answer / ajivadakkedathu
VSB transmission reduces bandwidth of the transmitted
signal. Since it is very difficult to separate carrier at
the receiver (video frequency range - 0 to 5MHz), distortion
may occur to low frequency components in the spectrum.
Because of this, a portion of LSB is also transmitted.
| Is This Answer Correct ? | 4 Yes | 6 No |
Answer / niyati
in ssb transmission some information is lost also it is
some what complex,so vsb is used for television signal
transmission as it has two signal one is audio signal and
another is video thus one side band ,carrier,and some
portion of another side band is transmitted,so complete
information is transmitted without any losses.also bandwith
and power can be saved using vsb.
| Is This Answer Correct ? | 1 Yes | 4 No |
Answer / raveesh83
If we use the SSB technique and transmit picture
signal,then some portion of the other side band is also
transmitted. This is due to the transition band of the
actual filter which is quite large. If the cut off freq is
1000Hz with a transition band of 2.5% , then 1250Hz is
passes through that band. This is utilized in transmission
of picture signals.
| Is This Answer Correct ? | 19 Yes | 25 No |
need previous placement test papers of infosys and soctronics
What is piv of a diode in a rectifier circuit?
what is up linl?
What are the difference between UPS and VFD
WHAT IS RESISTOR?
how an emitter coupled logic works?
Explain why gold is added to the p-n junction?
How the FM 200 System is work? Just give me a reply about the Fire Incident and then Suppression by FM 200 step by step? Regards, ZahIR Uddin Babar For, BAFFESCO
What is an excess-3 code?
i am electronics & comm engg & appling 4 the AAI jr executive (electronics/ATC) written test. pls forward me the syllabus & old question papers.I will be very much thankful to you akil403@yahoo.com
how there is a 180 degree phase shift in output signal of CE amplifier?
how we can calculate antenna dimension for any em wave??
-
Civil Engineering (5086) - Mechanical Engineering (4453)
- Electrical Engineering (16638)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
