Can Induction motor run at over rated speed? ( 15oo rpm is
rated speed for 50HZ. is it possible to ride 3000 RPM with
same motor with the help of VVVFD for continues ride of
100HZ)

Answers were Sorted based on User's Feedback



Can Induction motor run at over rated speed? ( 15oo rpm is rated speed for 50HZ. is it possible to..

Answer / shyam

yes, we can run the IM above the 1500 RPM with variable
freqency device keeping the voltage constant at above the
rated voltage.but the life span of the motor may get
effected.

Is This Answer Correct ?    12 Yes 0 No

Can Induction motor run at over rated speed? ( 15oo rpm is rated speed for 50HZ. is it possible to..

Answer / predator

Dear How is it possible, Because the company give the rated
speed to that motor is 1500RPM. If we increase the speed to
3000RPM WRT VVVF, that speed should affect it's whole life,
means gradually damaged the motor's bearing, windings
thanks

Is This Answer Correct ?    9 Yes 3 No

Can Induction motor run at over rated speed? ( 15oo rpm is rated speed for 50HZ. is it possible to..

Answer / girja shanker

Yes, for using Varriavle Speed Drive Panel.
This panel will change Friquincy & Voltage.

Is This Answer Correct ?    2 Yes 4 No

Post New Answer

More Electrical Engineering Interview Questions

can v rotate single phase induction motor in both the direction...?

1 Answers  


Brief me about maintenance planning & sheduling of machine tool.

0 Answers   HCL, Thermax,


what is the formula for converting KW into KWH ?

3 Answers   Blue Star, Essar,


what ll happen to current if two phases get short circuited

2 Answers   Kirloskar,


what are the possible reaons & remedies if resistance of NGR getting heat up

0 Answers  






what is the mean of short circuuit current ( for ex. 50KA)?

2 Answers   Weltech Engineering,


What will happen if " not connecting the neutral point to ground of diesel generator output (380 V)", also if someone touched one phase without isolation from ground during the A/M condition what will happen to him?

3 Answers  


how to calculate the step resistance for slipring induction motor,how you deside the no of step for that?

0 Answers   ABB, Visa,


how much test voltage should applied for tan delta test.

2 Answers   Electrical, TATA,


What will be advantage if we put some load in neutral of grounded star transformer & loadshortcircuit current,rated current of cable & MCB with example?

0 Answers  


if we have a industrial load of 400 kilowatts with 415 volt AC then how much total harmonic distortion (thd%) should be acceptable for steady power system.

0 Answers  


tell me the operation of ELCB. How it detects a fault?

4 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16632)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)