Answer / sachin pawar

the min. compressive strength of bricks is 3.5 n/mm2

sachin
BLA POWER

Answer / prakash

3.5 N/mm2

Answer / mohsin ahemad

Compressive /Crushing strength of bricks (Indian Made) are very variable, and may vary from 30 kg/sq. cm to 150 kg/sq. cm for hand-made burnt bricks, while Crushing strength of heavy duty bricks machine pressed (also called engineering bricks) may have compressive strength as high as 450kg/sq. cm, and even 500 kg/sq. cm. The minimum crushing / compressive strengths of burnt bricks tested flat-wise prescribed are:
(i) Common building bricks—35 kg/sq. cm,
(ii) Second class bricks—70 kg/sq. cm,
(iii) First class bricks— 105 kg/sq. cm.
(iv) Crushing strength of bricks not less than 140 kg/sq. cm are graded as AA class.
The strength of bricks decreases by about 25 per cent when soaked in water.
Strength of sun-dried (unburnt) bricks is from 15 to 25 kg/sq. cm.
Water absorption of bricks after 24 hours immersion,
First class bricks—20%,
Second class bricks—22 %,
Third class bricks—25%.
Heavy duty machine made bricks should not absorb more than 5% of their weight.

Answer / amol kalokhe

Min.compressive strength of a birck is 3.5N/mm2

It depends upon the class of brick we are using.

please refer IS 1077 clause 4.1,page no.1

Answer / prashanth

3.5 n/sqmm

Answer / sakal

as per Is:2512 Part II

Min . Requirement Is 5 Mpa in aveg.
& 4 Mpa in Individual.

Answer / shailendra dubey

As per IS:1077, The min. compressive strength when tested
flat shall not be less than 8.4MPa for individual bricks
and 10.5MPa for average of 5 specimens.

Answer / raju nayak telangana

3.5Mpa as per IS CODE is minimum compressive strength of bricks in case of dry state

Answer / aman

3.5 n/sq mm. minimam compressive strengthbn of bricks

Answer / dheerendra pratap singh

3.5 n/mm2

i am laying a base of dimensions 6.5feet by 7feet by 1.25 feet depth how many bags of 25kg cement and how many bags of 25kg sand will i need

0 Answers  

parts of stair-case?

3 Answers  

How much percent of steel use in concrete members etc.slab,beam,lintal,colmn,raft fondation according to concrete volume? Kindly reply me I am in dbout plz

3 Answers  

what is the procedure for batching plant calibration??????

1 Answers   BCET,

Middle point of any slab is raised 10-12 mm during shuttering work because––

4 Answers  

12 mm dia not available at site for raft, 10 mm are available at site how to calculate?

8 Answers  

what is the meaning of degreasing of the euipment or line.

1 Answers  

Define What is made from large rocks, which protects the base of cliffs?

0 Answers  

Design a reinforced concrete combined footing (rectangular) for two columns located 3.60 metres apart. The overall sizes of the columns are 40cm x 40cm and 69cm x 60cm and the loads on them are 1000 kn and 1500 kn respectively. The space available for the width of the footing is restricted to 180cm. The S.B.C. of the soil is 280 kn/mm2 use M15 concrete.

0 Answers  

What is all weather canal

1 Answers  

specific gravity of block cotten soil, normal, rockysteta

1 Answers  

Prepare a Schedule for a Highrised building from starting stage to Handover?

0 Answers   bscpl,