Interested to Buy Any Domain ? << Click Here >> for more details...
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
How can i calculate the Breaking capacity of molded case circuit breaker, is the breaking capacity of CB for Diesel generator shall be less than grid supply's breaker ?
2243Test on three subjects Physics, Chemistry & Biology are to be conducted simultaneously the number of candidates for the tests are 68, 36 and 72 respectively. Candidates are to be seated in different rooms such that each room will have candidates of the same subject and the load on each invigilator be the same i.e. the number of candidates in each room should be the same what is the minimum number of rooms you need for the purpose
2 9466why different types of sound are produced in different bykes though they say run on SI engine
3 7887I have a 3 phase 600 volt prim. feed and a 120/208 sec. Isolateing tranformer .We are using this system for safety against shock . What is the proper grounding ?? Does the common on sec. get earth ground ???
1 3505
How we connect a instrument with ground, Give brief explanation with help of diagram?
how IDP Qury perform by the B subs MSC for MTC call. If subscriber is in roaming in other state? plz explain briefly
Discuss Garment sourcing.
what is difference between earthingpits,earthing grid & earthing mess?
I am a B Tech student n am very much interested in science n math.in which site i can find more concept regarding ECE?
What do you mean by an instrument transformer?
What is an ideal transformer?
need the type of technical questions in written test
HOW CAN WE MEASURE THE L SHAPE SURFACE OF THE MOMENT OF INERTIA AND SECTION MODULUS
What does a construction cost covers and what does not?
Which would you use - hydraulics or pneumatics?
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
Sir , i am a Mechanical Engg Student. Pls send me the JinDAL STEELS AND POWER LIMT.. RECRUITMENT DOMAIN AND APTITUDE BASED SAMPLE QUESTION Papers.. JINDAL IS MY DREAM JOB..PLEASE HELP ME AND GUIDE ME TO BE SUCCESS,I NEED THE SAMPLE QUESTIONS FOR URGENT. MY ID--sampathsurya@yahoo.com.
write a program that changes 74H to 47H in 8085 assembly programming
why -48 volts dc used in telecommucation
