Answer / ishwar soni

router is communication device that manly use to comunicate
two or many diff network route.

Answer / rohit

Router is a communicating Device use to communicate two Diff
network device in a network.
Router is used to chose the shortest path in a network.
It used to connecting to LAN. it works on ip address.

Answer / nishant mendhe

Rauter is a device or computer which is used two,three,four
or more IP networks

Answer / prashant vanarase

a router is a intellegent device.
a router routes between different sub-nets.
each port of a router belongs to different sub-net.
each port of a router is a member of seperate collusion or
broadcast domain.
a router uses routing table to take fordwarding decision
routing table is a layer 3 table and hence router is a layer
3 device.
routes in routing table can be entered statically or
dynamically.

After how long eigrp protocol advertise its routing table?

0 Answers  

---

Differentiate between broadcast domain and collision domain

0 Answers  

---

In Novell's use of RIP, there are two metrics used to make routing decisions. Select the two metrics. A. Ticks. B. Hops C. Loops D. Counts

3 Answers  

---

What is the purpose of ARP? A.) IP to host name resolution B.) Host name to IP address resolution C.) Mac to IP address resolution D.) IP to Mac address resolution

2 Answers  

---

What is HSRP and what is difference between HSRP and GLBP

2 Answers   Infosys,

---

---

Can Anyone tell what is aummarization??

5 Answers   Wipro,

---

Which of the following are used by routers to learn routes to be added to the routing table? Ping and Traceroute MAC address resolution Acknowledgments and Sequence Numbers Routing updates and static routes

1 Answers  

---

2. What are the valid ways to segment a LAN? (Choose all that apply) A. Repeater B. Bridge C. Switch D. Router

2 Answers  

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

When ospf protocol advertise its routing table?

0 Answers  

---

Identify the command to display the configured IP routing protocols? A.) show protocols B.) show protocols all C.) show routing-protocols D.) show ip protocols

2 Answers  

---

Which OSI layer provides mechanical, electrical & procedural specifications for activating, maintaining physical link? A.) Presentation B.) Network C.) Application D.) Physical E.) Transport F.) Data-Link

1 Answers  

---