Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Any one Give me formula for to increse the power factor,
0.8 to 0.95, How much the KVAr Required

Question Posted / pasuvaraj

9 Answers
13327 Views
Emerson, Rajshree Sugars, Siemens, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / thowsif_emerson_csm team

Calculation of Required Kvar:-

Initial P.f-PFi , Desired P.f-PFd and Real Power of Load in
KW...

KVAR=KW(tanAi-tanAd)

where,

Ai=Cosinverse(PFi) = Initial Power Factor Angle.

Ad=Cosinverse(PFd) = Final Power Factor Angle.

For Example:-

PFi=.85 & PFd=0.9 & Real Load=50 KW

For this required KVAR is 6.7 KVAR....

Is This Answer Correct ?

11 Yes

4 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / thowsif_emerson_csm team

Hi Pls Provide me the following Details:-

Input Load in KW....

Is This Answer Correct ?

7 Yes

2 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / sonam sherpa

P.F = M.D*(Tan(cos-1 x)-Tan(cos-1 y))

M.D - max. demand.
x- Actual power factor
y- Required power factor

Is This Answer Correct ?

4 Yes

0 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / stanley

pls verify the whole questions. i just already give the
formula with examples.

Is This Answer Correct ?

2 Yes

0 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / sonam sherpa

in above formual P.F- Capacitor rating in Kvar

Is This Answer Correct ?

2 Yes

0 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / rupesh sharma

kvar= kw(tan phii- tan phir)

Is This Answer Correct ?

2 Yes

2 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / akhilesh singh

please go through V.K.Mehta's book (power system)

Is This Answer Correct ?

0 Yes

0 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / sk rafiquil islam (kaithi,jamu

p=1.732*v*i*cos phaii so cos phai=p/(1.732*v*i) so,we can decrease of current we can developed pf

Is This Answer Correct ?

0 Yes

1 No

Any one Give me formula for to increse the power factor, 0.8 to 0.95, How much the KVAr Required..

Answer / ravi

Hi All,

Can u pls provide me the correct formula to calc.
P.f?????????????????

Is This Answer Correct ?

1 Yes

3 No

Post New Answer

More Electrical Engineering Interview Questions

HRC full from

6 Answers

What is Delta Connection? What is meant by Forward Delta & Reverse Delta & How Will be the Connection in Power Transformers?

0 Answers

How to test the thyresitor or SCR by multmeter?

5 Answers ABB,

basic differance between electrical and electronic.

1 Answers Jindal,

what is the significance of positve n negative voltage regulation .on alternator

1 Answers TCL,

What kind of earthing method can be useful for ships and boats ?

0 Answers GE,

An 8 pole, 50 Hz, 3-phase IM is loaded to a poing where pull out torque will occur. The rotor resistance per phase is 0.3 ohm and motor stalls at 650 rpm. The slip when motor stalls is A 1 B 0 C 13.33% D 10.33%

0 Answers

WHY FEEDERS TRIP IN COLD AND FOGY WEATHER?

2 Answers

why we use Test Terminal Block in 11 KV and 33 KV electrical panels.

0 Answers EMC,

whycircuit breaker is not connected at the generator end where the capacity of the generator is more say 60MW, 100MW etc.

2 Answers Adani, Adani Power,

what could be the RMS value and average value of a 4 phase sine wave?

0 Answers BARC,

what is meant by impulse voltage?

0 Answers Masseera,

For more Electrical Engineering Interview Questions Click Here