why the three phase transformer's star point does not sparks or seperated

why the three phase transformer's star point does not
sparks or seperated? while we often see that two phases
touches each other it sparks and ocationaly conductor
breakes out.

Question Posted / engr rb

4 Answers
8382 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

why the three phase transformer's star point does not sparks or seperated? while we often see..

Answer / nagaraju

Hi,
Three Phase star connected or delta connected windings are
divided with phase angle i.e 360/3=120. So in A.C the phase
sequence is changing alternatively. But any time if you do
the Vector sum of the three componenets Result is zero. If
not spark will occur in that situation....

Is This Answer Correct ?

4 Yes

0 No

why the three phase transformer's star point does not sparks or seperated? while we often see..

Answer / kundan

at a time when all three phase are live,they have pik valyu
is +x,-x and 0. that mean if r is +50 that time b is -50
and y is 0, all calculation is =50-50+0=0. so total
voltage is 0 v.
if this is not real ans pls send me accual fact.

Is This Answer Correct ?

1 Yes

1 No

why the three phase transformer's star point does not sparks or seperated? while we often see..

Answer / dhaval

nagaraju your ans is ok but if there is a phase dif and not
short ckt in transformer point so why we can not transform
all phase by bunching that is also is transformer out put..

Is This Answer Correct ?

0 Yes

0 No

why the three phase transformer's star point does not sparks or seperated? while we often see..

Answer / manojkrishnan

explain which side of the transformer - ( primary or
secondary )?

Is This Answer Correct ?

0 Yes

6 No

Post New Answer

More Electrical Engineering Interview Questions

Why we use Electrical energy rather than any other type of energy, mostly? Explain behavior of open secondary CT and short circuited secondary PT in energized condition?

0 Answers

HT/LT TRANSFORMER TEST?

0 Answers

What it the purpose of parallel phasing transfomers??

4 Answers ABB, Reliance,

what is the accaptable voltage between neutral to earth & How to reduse the resistance of earth in chemical earthing

4 Answers

When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<

0 Answers Lupin,

Meter p.t. ratio= 3×230/400 , c.t.ratio = 3×1 (2) A what is m.f.

0 Answers

what is strip power factor?

0 Answers TATA,

Is it possible to operate a synchronous 2-poles turbogenerator with a still-in-place faulted bar but electrically disconnected ???? If yes, should I act on the other phases as well ???

0 Answers

How to know vacuum in vacuum cylinder of breaker in working condition

0 Answers

DRAW ACIRCUIT DIAGRAM OF 100 KVA 415V/55-0-55V DELTA TO STAR TRANSFORMER

0 Answers SRA,

Which motor will you choose which can operate in both lagging as well as leading power factors?

0 Answers HPCL,

what are the compensations considered while designing a transmmision line.

1 Answers

For more Electrical Engineering Interview Questions Click Here