what will happen when a bulb s connected btwn two phases of a three phase delt

Categories >> Engineering >> Electrical Engineering
Suggest New Category

what will happen when a bulb s connected btwn two phases of
a three phase delta connected source?

Question Posted / senthil.spec

6 Answers
7679 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / sachin

As per our system, Vtg between two phases is 415V.so bulb
glows brightly for sometimes after that it may be blow-out
due to high vtg.
The reason, bulbs are specially designed for 230V AC.

Is This Answer Correct ?

16 Yes

3 No

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / raja

if the frequency between the two phases are differ then
the bulb is blinking according to frequency difference(f1-
f2)

Is This Answer Correct ?

11 Yes

2 No

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / mahavir jagdev

Actuallt it has multiple answers as the bulb and the voltage supply specifications are not given

I am assuming it to be a normal domestic bulb of 220 volts connected to a 415 v delta supply. The phase to phase voltage is 415v and the bulb will blast.

Is This Answer Correct ?

2 Yes

1 No

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / kuldeep

as given above answer the bulb is blast

Is This Answer Correct ?

1 Yes

1 No

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / tstar

If it is like delta connected for line to line and no neutral then, one side of delta connected bulb will glow brighter,the other two sides will go dimmer, probably one side of it won't glow.

Is This Answer Correct ?

0 Yes

0 No

what will happen when a bulb s connected btwn two phases of a three phase delta connected source?..

Answer / robin

Nothing would happen if there

Is This Answer Correct ?

1 Yes

8 No

Post New Answer

More Electrical Engineering Interview Questions

WE ARE PLACE A NEW 75 KW MOTOR FOR JPF.IT IS CONNECTED IN M.C.C. WHEN WE ARE STARTING M.C.C.INCOMER IS TRIPPED.THEN WE ARE CONNECTED IN P.C.C WITH A MM30 RELAY PROTECTION THEN WE ARE STARTED MOTOR WILL RUN SMOOTHLY.

0 Answers

What is the difference between expansion joints & thermal expansion joints in Bus bar

1 Answers

which is better 50 HZ supply or 60 HZ supply?

6 Answers

What is generator

1 Answers Mytrah Energy,

where the Motorized mccb to be used? In Motor control center panel starters ,it is use full. please answer

1 Answers Voltas,

why substation rating interms of 11 multiples???like 11kv/33kv iis there any special reason???

5 Answers

In PFI plant one stage capacitor connection is directly connected(with out megnetic contact controll). but why?

0 Answers Aegis,

Befor synchronissation of Generator what test to be carried out.pl.specify with reason.

3 Answers Kanoria,

as we see that in our country the power rating for transmission is always rated in multiple of 11 like 11kv,33kv,66kv132kv. So i want to know wht is reason or logic here.

2 Answers

what are types of ups?

1 Answers

what is the difference between Power and Distribution transformers ?

0 Answers

In the Variable Voltage Variable Frequency Drive, how the Voltage and Frequency varied ? Is it varied in the Inverter part of the Drive ? Please give us supporting document if any.

0 Answers

For more Electrical Engineering Interview Questions Click Here