Hi How can you start-up the 40w tube lite with 230v AC/DC without using any cho

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Hi How can you start-up the 40w tube lite with 230v AC/DC
without using any choke/Coil.

Question Posted / bhaskarp

5 Answers
13086 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil...

Answer / victorvgp

it's possible by means of Electronic choke.

otherwise it's not possible to ionise the particles in tube
light, with normal voltage.

Is This Answer Correct ?

13 Yes

8 No

Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil...

Answer / kalpesh

By using resistor for if supply is DC, and if AC supply use
high impulse for tube series manually connect starter
connection for less than 1 second the tube light glow with
this trick.

Is This Answer Correct ?

4 Yes

1 No

Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil...

Answer / jawed

you use the 100w lamp by replace the choke

Is This Answer Correct ?

4 Yes

4 No

Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil...

Answer / prakash

Is This Answer Correct ?

0 Yes

3 No

Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil...

Answer / ganeshiva

it's possible by means of Ac Transformer that produces Voltage above 1000Volts...
Try it and CONFIRMED MY ANSWER

Is This Answer Correct ?

6 Yes

11 No

Post New Answer

More Electrical Engineering Interview Questions

what is the criterion for selecting vector group of Transformers ? i mean how to decide vector group of Generator transformer, substation trasformer and transformer at consumer end

0 Answers Areva,

lightning arrester rating selection procedure: (line to line voltage(kV)/(squ.root of 3))*squ.root of 2. now the question is, IS this above formula correct for both STAR and DELTA connected system???

1 Answers

29 Which of the following breaking method save energy? A regenerative breaking B plugging C dynamic breaking D none of above

1 Answers

how can service sitting be setted for MCCB?Example for sittings IR (CURRENT RATING),IS(CURRENT STARTING)IO (current operating)?

0 Answers

IF 3 NOS.OF HEATERS,3KW CAPACITY EACH,1 NO.HEATER CONNECTED IN R PHASE,1 IN Y PHASE AND 1 IN B PHASE.THEIR END POINTS CONNECTED IN STAR.IF I CONNECT THIS STAR POINT TO NEUTRAL OR DO NOT CONNECT TO NEUTRAL.WHAT WILL THE DIFFERENCE.

3 Answers

why neutral wire thin than phase wire in 4pole conductor

5 Answers Hero Honda,

IN SOME CASE, WHEN I GIVE 24VOLTS DC AS INPUT, WHILE IN OUTPUT (THAT MEANS TERMINAL SIDE OF THE INSRUMENTS) I,M RECEIVING ONLY 6 VOLTS, WHAT IS THE REASON FOR THAT MUCH VOLTAGE DROP?

3 Answers

what is the formulae for selcting capacitor bank to increas pf

3 Answers

how to test vector goup of Dy11 transformer

1 Answers APPSC,

11 kv input, 66 kv input advantages

0 Answers

Name different types of fault and which instrument is used to measures earth,short,open cicuit fault?

6 Answers NTPC, Vijai Electricals,

what is the effect of back reactive power on the generator ?

0 Answers MRF,

For more Electrical Engineering Interview Questions Click Here