Answer / santosh chinchalkar

If T.G set is running on synchronus speed and turbine is
triped on low steam pressure or some other resion, The
Generator will take the power from system instated of
giving and Generator will work as Motor,that will harmful
to Turbine blades.for avoiding this reverse power
protection are used to stop the Generator.

Answer / ashiesh

The gemneraTor wiLL start behaving as motor, & will consume
power instead of generating.
But will simply stop if it has a reverse power protection
system.

Answer / ramji

The Generator will run still since there some steam trapped
in Turbine.This suitation is called Low Forward Power since
there is not enough Steam to run the Generator in desired
speed.This occurs because of some trapped steam in turbine
for some seconds.Now Days special vents doors are designed
in turbine to release these steam on account of tripping of
turbines

But Normally in protection Trip Logic of Generators there
will be Class:A,Class:B,Class:C

For Class A Gen Breaker will trip for below faults
U/V Stage-2 , O/V , Low Forward Power,Reverse Reactive
power,Neg Ph Seq ,Over Voltage

For Class B Turbine Breaker will Trip which also trip Gen
breaker instantly for below faults

Differential protection , Restricted Earth Fault .....


For Class C Grid Breaker will trip for below faults

Over Frequency and Under Frequency Under Voltage stage-1
and Over voltage

Because when you trip Gen Breaker for Undervoltage it will
result in whole plant black out so for stage-1 tripping of
grid breaker will do

similarly for All turbine faults the Gen Breaker is tripped
so that it is isolated from the system

Answer / vivek

main breaker will be trip and annunciator will show
tripping prob.

Answer / dayal varma

automatically the output of the generator stop.

Answer / vikas kallewar

TURBINE RUNNING IN SOLO MODE. if turbine trip at that time
generator also trip. due to under frequency,under
voltage,and 86T WILL TRIP TO 86G.
TURBINE RUNNING IN PARRALAL MODE GENERATOR TRIP TO RPR
PROTECTION

Answer / arindam

When Turbine trips, the dc excitation voltage which is
applied to the rotor through slip ring also trips,so no
excitation was there in the rotor means no flux cutting in
the stator.So generating voltage will be zero. So it will
nither act as generator nor as a motor. Its simply rotate &
due to moment of inertia,it will come to zero in short time.

Can we generate 3 phase power from single phase connections?? If yes, how?

2 Answers  

What will happen when we connect 2 bulbs in series between 2 phases

7 Answers   Pepsi, PowerTech,

 where the Motorized mccb to be used? In Motor control center panel starters ,it is use full. please answer  

1 Answers   Voltas,

which motor is used in electric train...???????

27 Answers   ESPL, IOCL,

what are the 6 terminals of the motor plss give me in details

5 Answers   Siemens,

HOW TO SIZE THE TRANSFORMER OR WHAT ARE THE STEPS INVOLVED IN FINDING THE SIZE OF THE TRANSFORMER FOR GIVEN LOAD SAY 2000KW ?

1 Answers  

what is deffrent alternatid and gernater

2 Answers  

What is the difference btwn grounding and earthing?

11 Answers   HAL,

Define maximum demand?

0 Answers  

defult setting in p220 micom motor proction relay for 11kv,640kw,f.l.a.-40a,1440rpm ht motor?

0 Answers  

what precautions to be taken while desigining a LT,HT panel. Eg-LT panel PCC panel with ACB installed. HT panel VCB panel with VCB installed. & what is main diffrence betwn IP54 & IP55 construction of panel.

0 Answers   Bhel,

Why do we have 110V, 230V, 415V etc. in electrical transmissions? Why not 100V, 200V,400V?

4 Answers