IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / dinesh

11 Answers
13501 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / abhijit

it is high tension

Is This Answer Correct ?

41 Yes

2 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / guest

high tension

Is This Answer Correct ?

24 Yes

2 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / pradeep

ofcourse high tension .. we have LT motors too that is low
tension ..

Is This Answer Correct ?

17 Yes

2 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / abdul nazir

Ans# 5, go and study again the subjects.
its high tension.

Is This Answer Correct ?

16 Yes

3 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / venkat

HT means high tension

Is This Answer Correct ?

14 Yes

2 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / ravinder

High tension

Is This Answer Correct ?

8 Yes

1 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / alexis

when we are talking about motors HT refers to high Tension
and LT refers to Low Tension, the term transmission refers
to transmitting power through a High tension cable in
electrical distribution system, and have no any relation to
motor...

Is This Answer Correct ?

6 Yes

1 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / g.venkatesh

high tension

Is This Answer Correct ?

2 Yes

1 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / dilli babu

HIGH TORQUE

Is This Answer Correct ?

0 Yes

0 No

IN HT MOTOR HT REFERS TO HIGH TENSION OR HIGH TRANSMISSION?..

Answer / ravi

GUY'S THAT IS NOT "TENSION" OR "TRANSMISSION" .IT IS "HIGH
TORQUE" , "LOW TORQUE"

Is This Answer Correct ?

2 Yes

20 No

Post New Answer

More Electrical Engineering Interview Questions

why usa use 60hz and 110v?

2 Answers

how to set the overload setting in the thermal overload relay?? is there any calculation in that??

3 Answers

Can RCD's used to protect the VVVF drive if not why.

0 Answers

What is shunt voltage and u v voltage witch one best

0 Answers SEL,

11KW Delta motor is taking about 44Amps in star and goes upto 70Amps in delta and trips OFF. The rated current is 26Amps. Application is for the blower. The motor takes ( no load without coupling impller ) only 2.5A and 5Amps in star & delta starter test.Need to know why its taking high current.

10 Answers Pfizer,

in three phase 11kv transformer (11kv/433v) input( R,Y,B) output (X,Y,Z,N) the connection as follows 1 phase R -open 2phase y connected to both R and y of input] 3phase B- B what is the output voltage X to N ,Y to N , Z to N

2 Answers Bescom,

Why reverse relay used

2 Answers cpgn,

The power dissipated by a resistor of 10ohm when a current of 2A passes through it is:(a) 0.4W(b) 20W(c) 40W(d) 200W

2 Answers

How to calculate Earth busbar size & what is the procedure we make for determine that?

1 Answers

How to specific gravity of battery will check, i didnt saw any hydrometer. & say me how to dip into the battery what are the specifications are given in the hydrometer?

1 Answers

What are the questions asked in PRDC pool campus test?(bangalore)

1 Answers PRDC,

State nyquist stability criterion.

0 Answers

For more Electrical Engineering Interview Questions Click Here