Interested to Buy Any Domain ? << Click Here >> for more details...
I have recently seen a transformer which had two primary
terminals and was connected between two lines,i would like
to know what kind of transformer is it?short discription
about it,any advantages,purpose of usage of the
same.............
- 8 Answers
- 11028 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Types of Bushing transformers:
One bushing transformers & Two bushing transformers
One bushing transformers:
The one bushing type has one terminal for the primary hot
to connect to. One bushing transformers are used mainly for
setup up three phase transformer banks, since the terminals
are located in a little better position for this type of
setup.
Two bushing transformers:
The two bushing type (most common) have two primary
terminals on top of the pole can for both primary
conductors to connect to. . The second primary terminal in
on the back side of the can (180 degrees opposite the
secondary terminals)
| Is This Answer Correct ? | 2 Yes | 0 No |
please give more relevent details. how you guess it is primary terminals ,how many phase. used where .how many kva .the secondary connected where, how many volts.without some guiding information nobody can really help, every body can just guess something and in the end nobody benefits.
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / vinothbabu.k
This type of Transformer will have two type of voltage
conversion..For example-440/230 & 440/110 or 440/230 &
230/110.
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / vinothbabu.k
This may have two feeder from Different substation,if one
fails another will be feed supply,this for uninterruped
power supply to consumer side...
| Is This Answer Correct ? | 3 Yes | 4 No |
Answer / madhu
not sure:
but it may be booster transformer in which the line
itself acts as primary and secondry is supplied with
another source.
| Is This Answer Correct ? | 0 Yes | 2 No |
Answer / gaurav
Not the exact answer i am looking for........
Can anybody please tell me in more detail's?
| Is This Answer Correct ? | 0 Yes | 3 No |
Answer / gaurav
BUT BUT
its not transmission or distribution transformer my friend
its inside a machine which uses three phase supply
| Is This Answer Correct ? | 0 Yes | 3 No |
Answer / manjunatha
my it may be communication purpose were in 440v reciving
stations TO genarating station there is direct
communication line
| Is This Answer Correct ? | 0 Yes | 3 No |
In power transmission using open belts or horizontal shafts it is preferable to have the slack side of the belt on the top because
What is transformer tap changers please explain
3 Answers Feedback Venture, Sail,
how calculate cable size in squre mm, when the load is given by in kw? do u have current rating chart of elctrical cables?
What is an Antipumping relay ?
What is the difference between 2 wires RTD's and 3 wires RTD's.Kindly explain the wiring diagram.
can we use 7volt DC BATTERY to run a 60watt motor by stepup? Give reason for your answer?
What is the permissible maximum flux density in transformer core?
what is a bus riser in power system and why it is used
What is LMU and LMDU. in PLCC communication of 132 kv transmission line. is it possible to use only one LMU with out LMDU ?
i have installed my solar site of 6.7kw and is working perfectly , can somebody tell me that how can i measure my solar irradiation kw/day/sq m ?
what is neutral voltage
What should be value of Circuit breaker operating time and tripping time?
-
Civil Engineering (5086) - Mechanical Engineering (4456)
- Electrical Engineering (16639)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
