Answer / sanjeet

isolation transformer is basically used 4,isolate between to
electrical ckts and the turns ratio is always 1:1.

Answer / zahid ali

Dear Friend
Isolation transformer is used between two circuits for
Galvanic isolation. It is used to prevent the damage on the
source circuits, Like PLCs, DCS etc. in case of field
circuit shorted.

Answer / afrooz

isolation transformer is used to ups from damaged if there
any fault in the feild

Answer / tariq

Isolation Transformer is used to block the DC components.
It has 1:1 ratio.There are many causes to produce/introduce
the DC components. If we do not block these components then
if may effect on the output. Isolation Transformer can be
used within in a single circuit. So, it is not correct that
the isolation transformer is always used to isolate the two
circuits.

Answer / sasi karthick a

Isolation transformers are used to isolate the two sides of
the system with respect to electrical and introducing a
transformer will bring down the short circuit fault level
because of transformer impedance.

Tats y lighting transformer are considered even though for
same level of voltages.

Answer / suppu

isolatin transformer is used for reduse the leakage current

Purpose of providing neutral isolation panel for parallel operation of diesel generator

0 Answers  

how capacitor pass ac voltage practically?with increase frequency and cpacitance?

1 Answers   DELL,

what happen if field of dc shunt motor opens? what is function of putting res. in parallel to one phase of 3 phase IM? the power supplied by 5A source in circuit is given by------Watt.

0 Answers  

What are merits & De-merits of State-Space Method? What is series programming, parallel programming, general programming & direct programming ? And, difference between these programmings Techniques ?

0 Answers  

How can claculate to attain the desired PF in the line ( HOW Much KVAR is required ) Pls Give the formula? Equate Petrochemical 0 1 how to calculate sizing of NGTR (Transformer rating,Loading resistor value and Current rating of resistor) and what is the X/R ratio. Details : 11kV,Capacitance 1.73532 micro farads,40kA for 1sec. 0 1 What will happened. if we feed 3phase supplay to the stater with out insert the rotor. How much current will flow through the stater winnding? Equate Petrochemical 0 1 What is required of exietation to the alternater. 0 1 why star point of HT motor not earthed? Equate Petrochemical 0 1 Why we are getting low voltage in star connection? Equate Petrochemical 0 2 What's ND relay & it's functions? Equate Petrochemical 0 2 How instantanious short circuit current is calculated? its formula? Equate Petrochemical 0 2 What is servo Motor? What's the advantages of this motor over Induction motor? Equate Petrochemical 0 2 What is core CT & it's function? Equate Petrochemical 0 3 what is meant by star/delta voltages as 440/220 in a 3 phase induction motor, and why it should be connected on STAR IN 3 PHASE SUPPLY L & T 0 4 What is required of exietation to the alternater. KNB 1 23 what is the design voltage for 6.6KV 2000 KVAR HT capacitor? Consultancy 0 3 Pls explain about vfd control?Where it is used, Give some example? siemens 1 22 Please explain me abt PQ diagaram in the power sector. 0 9

0 Answers  

How do performance buccholz relay testing in power transformer

1 Answers  

what is the diffrantial relay???????why we use it on the MDB

5 Answers  

whatis mean by voltage?

7 Answers  

how to test the turn ratio of 3 phase transformer using volt meter shoe the curcit diagram.

0 Answers  

domine+aptitude test means?

2 Answers  

how to calculate the chiller load from TR to KW?

0 Answers  

what is meant by twilight switches 7 where its applicable ?

0 Answers