what is fault level in 66kV system?

Answers were Sorted based on User's Feedback



what is fault level in 66kV system?..

Answer / mohit.k.k

it depends on p.u impeadeance of supply transformer

Is This Answer Correct ?    4 Yes 0 No

what is fault level in 66kV system?..

Answer / gunasekaran

3000MVA

Is This Answer Correct ?    3 Yes 3 No

what is fault level in 66kV system?..

Answer / satya dev

Dear All can anybody explain the how to calculate the Fault
level in High voltage Distribution System

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Electrical Engineering Interview Questions

Determine the minimum cable size for a 28A single phase final sub circuit originating from the distribution board supplied by three phase submain. The route length of the final sub circuit is 54 m. Assume 1% voltage drop in the consumer's mains. Submain specification: Cable: 50mm2 4 core V75 copper; Route length 42m; Maximum demand 135A per phase

1 Answers  


why do we need to use 3c+3e cable, normally i select only 3c+e cable and i think it is enough. pls explain the usefull of 3e cable ( in this project the earthing system is well done)

0 Answers  


How the annunciator works ? How to do its wiring

0 Answers   Ford, MSEB,


For two systems transmitting the same amount of real power, the system with the lower power factor will have higher circulating currents due to energy that returns to the source from energy storage in the load.???

0 Answers   Bhel,


What will happen to magnitude of voltage of other two phases if one phasw will touch the ground?

3 Answers   Construction, NPCIL,






How to increase the specific gravity of DG batteries?

12 Answers   SCS,


For RCD (Residual current device) Icu is defined. How i can find Ics for them?

0 Answers  


What do you mean by 4.44 in this transformer equetion E=4.44 nfqm

4 Answers   Bharat Bijlee,


Why we are using Isolation Power Transformer inplace of commercial power transformer? What's the difference between them?

0 Answers   UPCL,


Generally transformers has delta primary and star secondary. But in some transformer i saw Star primary and delta secondary. what is the reason for chosing like this?

2 Answers  


An 11kv system consisting of an underground cable to a sub station about 300 meters away was shut down for about 10 hrs. On energising, it tripped off on earth fault about 10---20 mins later 6 times but since than it is not tripping.its already 3 weeks now. The SPAJ was found to be fine. what could be the cause.No test had been done to determine the cause of the trippings till now because of demand.

2 Answers  


List out the types and name of the motor under their application?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16636)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)