CHEMICAL MATERIAL BALANCE – EXAMPLE 2.6 : According to Raoult's law for ideal liquid, x (PSAT) = yP where x is mole fraction of component in liquid, y is mole fraction of component in vapor, P is overall pressure and PSAT is saturation pressure. A liquid with 60 mole % component 1 and 40 mole % component 2 is flashed to 1210 kPa. The saturation pressure for component 1 is ln (PSAT) = 15 - 3010 / (T + 250) and for component 2 is ln (PSAT) = 14 - 2700 / (T + 205) where PSAT is in kPa and T is in degree Celsius. By assuming the liquid is ideal, calculate (a) the fraction of the effluent that is liquid; (b) the compositions of the liquid and vapor phases. The outlet T is 150 degree Celsius.

1 Answers  

---

viscosty of crude use for petroliun?

4 Answers   ONGC,

---

What is the maximum steam pressure that can be generated?

0 Answers   CPCL,

---

Question 100 - (a) Time evolution in Heisenberg picture, according to Ehrenfest theorem is m (d / dt) < r > = < p >, where m = mass, r = position, p = momentum of a particle. If v = velocity, prove that m < v > = < p >. (b) Lande g-factor is given by Gj = Gl [ J (J + 1) - S (S + 1) + L (L + 1) ] / [ 2J (J + 1) ] + Gs [ J (J + 1) + S (S + 1) - L (L + 1) ] / [ 2J (J + 1) ]. If Gl = 1 and under approximation of Gs = 2, prove by calculation that Gj = (3/2) + [ S (S + 1) - L (L + 1) ] / [ 2J (J + 1) ].

1 Answers  

---

BIOCHEMICAL ENGINEERING INSTRUMENTATION - EXAMPLE 29.3 : In thin layer chromatography (TLC), let retention factor Rf = (distance traveled by solute) / (distance traveled by solvent). Silica gel is used as stationary phase which is more polar than the hexane solvent as mobile phase. If the Rf values of 3 solutes A, B and C are 1.5, 0.75 and 1 respectively, compare the polarities of A, B and C with reasons.

1 Answers  

---

what is meaning of pid how it is useing controlers

4 Answers  

---

what is the difference between distillation column and distillation tower?

3 Answers  

---

For a centrifugal pump if the pump is running and we close the discharge valve what is the effect

11 Answers   Asian Paints, NFTDC, Reliance,

---

ACCOUNTING AND FINANCIAL ENGINEERING - EXAMPLE 34.27 : A biochemical engineering consultancy applies construction accounting in its finance. Its project began on 1 January 2010. Total revenue generated from the project was $9000. On 1 January 2011 as the budget, $2000 had been spent, with $6000 expected. However, the project cost increased latter, causing deviation from its initial budget on 1 January 2012, where $7000 had been spent, with $1400 expected. Let (estimated total cost) = (spent cost) + (expected cost to be spent), (percentage completion) = 100 (spent cost) / (estimated total costs), (total expected profits) = (total revenue) - (estimated total costs). Calculate : (a) total expected profits on 1 January 2011 and 1 January 2012; (b) estimated total cost as and not as the budget; (c) percentage completion of the project since the project began, in the first and second years.

1 Answers  

---

What is the method of determining maximum differential pressure during hydro testing of shell and tube heat exchangers?

0 Answers  

---

What is a good relation to use for calculating tube bundle diameter?

0 Answers  

---

who is the first atomic scientist in india?

5 Answers   IGCAR,

---