Which of the following is True regarding passwords on a Cisco router? A. All passwords can be encrypted B. All passwords can be entered using the set-up dialogue C. A password can be set before a user can enter the privileged mode D. A password can be set for individual lines E. TACACS or Radius password authentication can be used.

1 Answers   TATA,

---

Which protocol switch use for filling its mac-table?

0 Answers  

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

Identify the 2 methods to modify the routers boot sequence? A.) Setup program B.) Boot system commands C.) RXBoot D.) Config-register

1 Answers  

---

hi all.. can any one explain the complete topology of stp and rstp how it works . root swtch connects to a root port and then root port conenct to other switchs designated port. i was going thru his site http://www.cisco.com/en/US/tech/tk389/tk621/technologies_whi te_paper09186a0080094cfa.shtml in which DR also exist on root switch only which makes my understanding grim.I had a diff notion of stp all together. please post asap. and if possible refer a url so thst i can read it my self .. thanks

1 Answers  

---

Which Standard IP Access list commands will deny only the source address 1.1.1.1? A.) access-list 9 deny host 1.1.1.1 B.) access-list 9 deny 1.1.1.1 255.255.255.0 C.) access-list 9 deny 1.1.1.1 0.0.0.0 D.) access-list 9 deny 1.1.1.1 0.255.255.255 E.) access-list 9 deny 1.1.1.1 255.255.255.255

5 Answers  

---

Which of the following is a layer 2 device? A.) Switch B.) Bridge C.) Repeater D.) Hub

2 Answers  

---

what hapeen we we configure default root on the router which is conected by isp supoese there are two router r1 is conected throug isp and and by s0 r1 is conexted to r2 if we apply degault root on r1 what will happen

3 Answers  

---

Which ISDN specification series deals with Concepts and Terminology? A.) World Series B.) I- Series C.) Q-Series D.) 911-Series E.) J-Series F.) F-Series

1 Answers  

---

What is the difference between cross cable and straight cable?

0 Answers  

---

How many LMI types are available on Cisco routers? A.) Four B.) Two C.) Five D.) Three

1 Answers  

---

Which of the following is an example of a Transport Layer protocol? Ethernet IP TCP RS-232

2 Answers  

---