1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

You have two Cisco routers setup back-to-back in a lab using

DTE/DCE cables. To which router would you add the clockrate
command?

A.) The serial port on the DCE router

B.) The Ethernet port on the DTE router

C.) The Ethernet port on the DCE router

D.) The serial port on the DTE router

Question Posted / guest

Answers were Sorted based on User's Feedback



You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router woul..

Answer / guest

Answer: A

In order to connect routers back-to-back, a clock rate must
be set on

the router with the DCE cable. This will provide the
clocking usually

performed by a DSU/CSU. It is recommended that a bandwidth
statement be

added to the interface because some routing protocols, such
as IGRP, use

this to make routing decisions.

Is This Answer Correct ?    11 Yes 3 No

You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router woul..

Answer / surya

sorry thats not DCR that should be DCE

Is This Answer Correct ?    7 Yes 0 No

You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router woul..

Answer / surya

In order to connect two Cisco routers back to back clock
rate needs to configured on serriel port of DCR router.

Is This Answer Correct ?    5 Yes 1 No

Post New Answer

More CCNA Interview Questions

Hello Mr.Jitendera Kuamr Sinha, how is every thing going on? Thanks for your reply. Dear Friend if you can Explain it little bit deeper i will be realy thanks full. Wish you all the Best.

1 Answers  

router

4 Answers   Infotech,

Given an IP host address of 172.16.2.160 and a shored mask of 255.255.255.192 to which shored does the host belong? A. 172.16.2.32 B. 172.16.2.64 C. 172.16.2.96 D. 172.16.2.128 E. 172.16.2.192

2 Answers  

HI friends mine one of the friends have ask a good question i also donot know the answer so i am putting here Please poet the answer no matter it is wright or wrong put yours view here The question is like that when we are going to configure ospf then there are three way 1st way router ospf 10 netwrok 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 the 2nd way is like that router ospf 10 netwrok 192.168.0.0 0.0.255.255 area 0 but he inrodused the thrird way like router ospf 10 netwrok 192.168.00000001.0 < ?.?.?.?>area 0 router ospf 10 netwrok 192.168.00000010 <?.?.?.?>area 0 now problem is that what should i put the mask in this way so i puted ? sign Please solve this problem i think this is good one plz donot see for answer please contribute any thing i am reqesting Than you Jitendera kuamr sinha

5 Answers  

Hub in star topology or bus topology?

0 Answers  




What does a metric of 16 hops represent when using RIP? A.) Number of hops to the destination B.) Destination unreachable C.) Number of routers D.) Bandwidth

2 Answers   IBM,

plz send me cisco contact no india?

0 Answers   3i Infotech, Cisco,

Which port numbers are used by TCP and UDP to set up sessions with other hosts? A.) 1024 and above B.) 6 and 17 respectively C.) 1-25 D.) 6-17

6 Answers  

How can we configure Inter-VLAN in Layer 3 Switch? Remember one thing without Router.

7 Answers   Grace, HCL,

What’s the default CDP holdtime in seconds for Cisco routers?

2 Answers  

What are the two types of access lists that can be configured on a Cisco router? A. Standard B. Extended C. Filtering D. Packet

2 Answers  

Which command can verify Application Layer connectivity between 2 hosts? A.) ftp B.) snmp C.) telnet D.) ping E.) traceroute

4 Answers   CTS,

For more CCNA Interview Questions Click Here
Categories