Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...

  1. Categories >> Engineering
  2. Suggest New Category

Question 96 - In infrared spectrum, one of the factors affecting peak location is the mass of the atoms. The stretching frequency of a bond connected to a lighter atom will be greater than the same bond connected to a heavier atom. (a) For halogens like florine (F), chlorine (Cl), bromine (Br), iodine (I) and astatine (At), what is their IUPAC group number? Hint : The proton numbers for F, Cl, Br, I and At are 9, 17, 35, 53 and 85 respectively. (b) For the compounds of H-F, H-Cl, H-Br, H-I and H-At, which one has the lowest stretching frequency and which one has the highest stretching frequency? State the reasons.

Question Posted / kangchuentat


Question 96 - In infrared spectrum, one of the factors affecting peak location is the mass of the at..

Answer / kangchuentat

Answer 96 - (a) 17. (b) Lowest stretching frequency : H-At. Highest stretching frequency : H-F. Reasons : F has the lowest proton number 9 and At has the highest proton number 85. For the compound of H-X, the stretching frequency of the bond decreases when the mass of X increases and vice versa. The answer is given by Kang Chuen Tat; PO Box 6263, Dandenong, Victoria VIC 3175, Australia; SMS +61405421706; chuentat@hotmail.com; http://kangchuentat.wordpress.com.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More Engineering Interview Questions

why water first pass to sac then sba

1 Answers   ACC,

If I installed wrong directions orifice plate then what showing value d.p transmitter in D. C. S. ?.....

0 Answers   TCL,

Why patra you join

0 Answers   Patra Corporation,

how we can calculate the load appeared on programable logic controller.and what is the method to calculate the scan time of PLC.

0 Answers   Siemens,

difference between gauges and comparator

0 Answers  

why we use transformers?

0 Answers  

what is the work of commutator and brush in motor

0 Answers  

Why we should not apply Ac supply to Cable when during the cable Hi pot test ?

0 Answers  

How to calculate the angle in electrical transmission line

0 Answers  

Handpump harness water dont go back.Why?

1 Answers   Focus Energy,

what's the defiance between T beam and inverted beam.

0 Answers  

In an existing power plant (phase I) with step up transformers (3nos) with Ynd1 vector group to the 400KV bus bar,an extension power plant (phase II) with transformers (4nos) with Ynd11 vector group >. what are the consequences of such configuration ,please note that % impedance are also differ i.e. 15% & 10.5% the reason was that auxiliary supply interface is at different voltage levels i.e 400v & 6.6KV in phase i and phase II respectively .please advise ! Thank you !

1 Answers  

For more Engineering Interview Questions Click Here
Categories