What will happen if we give 220v supply on both sides to the bulb

Categories >> Engineering >> Electrical Engineering
Suggest New Category

Question Posted / purna

7 Answers
11546 Views
Exide, Sumeet Industries, Toshiba, I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What will happen if we give 220v supply on both sides to the bulb..

Answer / deepak

bulb is not working because potential difference is zero so from ohms law current is zero.

Is This Answer Correct ?

17 Yes

2 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / murali karri

Always we talk about the potential by taking some reference it may be a ground or neutral. If there is no phase difference b/w those two 230v then the potential difference will be zero and no current will flow through filament.

Is This Answer Correct ?

3 Yes

1 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / archit_asthana

The resulting potential difference can be any value between 0V to 440 V depending on the phase difference of the two sources.

Is This Answer Correct ?

1 Yes

1 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / md

its depends on phase of supply .. i mean if u give R-phase to one side of lead and other side maybe B or Y phase ,, and if u r supplying both end with same phase

Is This Answer Correct ?

0 Yes

0 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / ashutosh pati

If we gave 220v supply in 2wires then supply ism 415v then the both side of bulb is not working for short time and the filaments are nit work. The bulb rating is limited.

Is This Answer Correct ?

0 Yes

0 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / maneesh

When we have give supply 220 in 2 wire then supply is 415 v then bulb is not work and blast because bulb rating limit cross

Is This Answer Correct ?

5 Yes

6 No

What will happen if we give 220v supply on both sides to the bulb..

Answer / abid

When we have give supply 220 in 2 wire then supply is 415 v then bulb is work for short time and give maximum light then blast because bulb rating limit cross

Is This Answer Correct ?

1 Yes

2 No

Post New Answer

More Electrical Engineering Interview Questions

How to reverse the direction of a DC motor ? By reversing the Armature wires or by reversing the field wires

2 Answers KFC,

can i use 2000/5A Clamp meter to measure HT cable

0 Answers century, Engro,

when a motor is connected in parallel with the existing motor the pf will change or not?

9 Answers

1. What does mean of "PS" stand for Diff. CT class? 2. What is the formula of KW for 1Phase load inturms of voltag,current & P.F.?

4 Answers Hero Honda,

Rated moter voltage and frequency is 380volt 60 hz but moter is running at 380votac 50hz is this harmful for moter winding

1 Answers Infosys,

is it ok to switch lights from a mcb instead of switches

5 Answers

what is the minimum (Common factor) insulatin resistance of the following a, 4mm sq wire b, cable from 50 mm sq to 800mm sq

0 Answers

State the difference between Surge Arrester and Lightning arrester,Both are same or not?

7 Answers

What is C.T, why it is used and what care should be taken for that while connecting?

20 Answers Bhushan Power Steel,

what the purpose of data retrivala panel in substation

1 Answers NCC,

What is sink and source?

0 Answers

Different types of relay fault which phase sequence??

0 Answers

For more Electrical Engineering Interview Questions Click Here