What is the Laplenth for Reinforcement for Verticl and horizontal Structures a

Categories >> Engineering >> Civil Engineering
Suggest New Category

What is the Laplenth for Reinforcement for Verticl and
horizontal Structures as per IS code?

Question Posted / guest

7 Answers
13238 Views
I also Faced
E-Mail Answers

Answers were Sorted based on User's Feedback

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / ravibabu bammidi

Dear

Lap length of bar depends on grade of concrete and design bond. so we get different lap lengths for different grade of concretes which are as follows
(Grade of concrete) Tension Compression
M15 56.4d 45.15
M20 47d 37.6d
M25 40.3d 32.25d
M30 3706d 30.1d

Is This Answer Correct ?

7 Yes

0 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / guest

48D

Is This Answer Correct ?

6 Yes

3 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / pranav panchal

Generally

50d for vertical structures

60d to 67d in horizontal structures

Is This Answer Correct ?

2 Yes

1 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / md jalaluddin mustaq

65D & 50D RESPECTIVELY

Is This Answer Correct ?

1 Yes

1 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / pranay

50d for vertacal and 60d for horizontal member

Is This Answer Correct ?

0 Yes

1 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / guest

ap length for vertical member As per IS code is 35D & lap
length for horizontal member As per IS code is 70D

Is This Answer Correct ?

2 Yes

4 No

What is the Laplenth for Reinforcement for Verticl and horizontal Structures as per IS code?..

Answer / kj

Vertical is a commpression member like coloumns etc and horizontal is a bending member.Depending on grade lap length will be determined.Horizontal will be more allways as bending stress.

Is This Answer Correct ?

0 Yes

2 No

Post New Answer

More Civil Engineering Interview Questions

How to find arc area with using angle?with out using angle?

1 Answers

Pile height is 4.3m. 2nos. under reammer. bulb nose is 75mm and height is 400mm. pile dia is 375mm and overall dia 940mm.pls. help to calculate concrete in pile and bulbs separately. What is formula for bulb volume calculation ?

0 Answers

what is the steel difference between np-2 and np-3 pipes and weight also

0 Answers

how we can find sieve #4 is 4.75mm?

0 Answers

What is the density of Cement, Fly ash,20 mm aggregate, 10 mm aggregate and stone dust?

14 Answers Amrapali, Egis, Himuda, Indramas, L&T,

What is the acceptable percentage of slump in Mix concrete?

9 Answers

What Should be the CBR Value for Transported (Selected) Soil.whether it can be 5% or not ?

3 Answers Jindal,

What are the effects of water on shear strength and foundations?

2 Answers

What is demising walls?

0 Answers

In foundation design, while we do the base pressure check, we normally check if the attained pressure value is less than the GROSS BEARING CAPACITY of the soil which is the sum of net bearing capacity of soil and the overburden pressure. Actually, the overburden pressure acts against the net bearing capacity of the soil and I feel that we are actually increasing the bearing capacity value and doing the check. I feel that this is NOT right. Please clarify on this.

0 Answers

IS code for Rolling Margin of steel

0 Answers

100mm block work 64 bags of cement used 150mm block work 286 bags of cement used 200mm block work 20 bags of cement used patly work (M15) 293 bags of cement used mortar ratio is 1:5 how to calculate volume of sand in cum & no. of bags

0 Answers

For more Civil Engineering Interview Questions Click Here