Answer / indira pati

there are 3 types of numbering codes...1)JEDEC: A transistor
is a digit,letter,serial.no. The first digit is number of
leads minus one means ordinary bjt have 3 leads minus one =2
next is letter N for semiconductors...serial no. gives the
info. abt the device operation and specification and we read
the packaging or datasheetto find them...some times extra
letters refers manufacturer. ex:2N7000

2)pro-electron : in this two letters followed by serial no.
the first letter represent the material means A for
germanium and B for silicon. second letter refers transistor
type C means small signal D means power Ex: BC789

3) JIS: in this digit, two letters, and serial
number...first digit 3 leads minus one...first letter is S
for semiconductor ...second letter refer to transistor type
A for high freq. PNP and C for high freq. NPN...sometimes 2S
is assumed it is not stated plained written on component
casing Ex: 2SB560... the label after read B560 where 2S is
assumed....

What is the need of filtering ideal response of filters and actual response of filters? What is sampling theorem? What is impulse response?

0 Answers  

---

Q.1. What do you mean by FDMA? Explain in details. Q.2. What are active & passive elements in BTS? Q.3. Name the equipments required for 2+2+2. Q.4. What is the function of BB2F card? Q.5. What is the function of BOI card? Q.6. Which modulation we use in case of GPRS? Q.7. Which slot is reserved for GPRS? Q.8. What is the height of BTS? Q.9. What is the height of ESMA card? Q.10. How many maximum slots we can use in ESMA card? Q.11. We use PSWA card in which case? Q.12. We use PSWB card in which case? Q.13. How many types of Transmission cards are in Ultra BTS? Q.14. How many types of Transmission cards are in Flexi BTS? Q.15. What will happen if we change the polarity of microwave antenna? Q.16. What is the full form of ARFCN? Q.17. What is the function of TRAU? Q.18. Explain the structure of entire GSM. Q.19. Explain the configuration of 4+4+4. Q.20. Which type of connector we use in FIFA card? Q.21. Which type of connector we use at the end of GSM antenna/ Q.22. What are the different types of GSM antenna? Q.23. What do you mean by Splitter? Q.24. Convert the 16 W power into dBm. Q.25. Explain the different steps of Commissioning. Q.26. What do you mean by protection loop? Q.27. What is the correct way of weather proofing? Q.28. Can we use 7GC instead of 15GC? Q.29. What is the function of Duplexer? Q.30. What are the different elements of MSC? Q.31. Write the total description of Ultra Commissioning.

0 Answers   Nokia,

---

Which type of architecture 8085 has?

3 Answers  

---

why have u choose btech?

2 Answers   Wipro,

---

i worked as microwave engineer and recently i am working as SDH engineer, i created some crossconnection but about the huawei MUX its difficult to find out the solution for any problems and exect way of doing the task? Please help me if any one having expertise on that area and SDH

2 Answers   Huawei,

---

what were the challenges you faced during the project technically and how did you cope up with that?

0 Answers  

---

Why is zener diode used as a voltage regulator?

0 Answers  

---

how to begin the answer for "tell about yourself"? also what to answer?

3 Answers  

---

send me few previous years section engineer question papers?..

0 Answers  

---

What are the maintenances of a PLC ?

0 Answers  

---

Normally we say cellphone is a embedded device but computer is not a embedded system. Today cell phones have the facility to install software. so the cell phone is embedded or not

4 Answers  

---

What is the ideal op-amp CMRR ?

0 Answers   Lucent,

---