Need to design filter...Length and diamter of shell



Need to design filter...Length and diamter of shell..

Answer / yash patel

Now i have posted all the required details .
Need to Design Filter .Where Polypropylene wound cartridge
to be fitted. Would you please help me carrying out the
design part. Especially length and Diameter of Shell.Please
help me out in performing calculations.Since i know now all
the basics .but one or the other hand its not getting solved
due to lack of knowledge.
If you don’t mind ,would you please solve it for my sake
once.

Type: Multiple Elements

Material Removed : PVC Particles

Design Data
Fluid Handled: VCM Vapor + Water Vapor
Flow M3/Hr Normal :318
Maximum:365
Density :2.67 kg/m3
Viscosity : 0.01
Operating Temp:54` C
Operating Pressure: 0.2 kg/cm2
Design Temp :170 `C
Design Pressure: 2.8 kg/cm2

Maximum Allowable Pressure Drop :0.01 kg/cm2
Desired Particle Retention, Filter Mesh to be Used:10
micron

MOC Shell: Carbon Steel
Filter Element: 304 SS
Inlet/Outlet Connections: 6 inch Flange
Vent/Drain Size :1 inch /3 inch
Line size : 6 inch
Clean Pressure drop across the filter: 0.006kg/cm2
Dirty Pressure drop across the filter: 0.02kg/cm2

Size of Filter Element:
ID : 30 mm
OD : 62 mm
Length : 750 mm

Where PP wound filter to be Fitted.

Please help me out.

Regards
Yash Patel
http://yashpatel.co.nr/

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More Chemical Engineering Interview Questions

Why chlorine cylinders are laid down horizontally?

3 Answers  


When should one be concerned with the tube wall temperature on the cooling waterside of a shell and tube exchanger?

0 Answers  


plz send the interview questions in the written test asked by hindustan petroleum corporation ltd.Iam a b>tech in chemical engineering.My written test is on feb 2008.urgent plz.send the questions to indra_bits10@yahoo.com

0 Answers  


why relative humidity is different in different places

3 Answers  


CHEMICAL ENERGY BALANCE - EXAMPLE 11.1 : Please match the term A - E with the stated definition i - v. Terms : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. Definitions : i. (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely); ii. (moles of desired product formed) / (moles of undesired product formed); iii. (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature); iv. (moles of vapour) / (moles of vapour dry gas); v. (mass of vapour) / (mass of dry gas).

1 Answers  






ENGINEERING ECONOMY - EXAMPLE 7.2 : In the purchase of a machine with a period n = 8.5 years, the minimum attractive rate of return, i = 12 %, the cost P = $55000, F = $4000 is the salvage, annual maintenance A = $3500. The return of the investment or equivalent uniform annual benefit is $15000. The equivalent uniform annual cost is P (A / P, i, n) + A - F (A / F, i, n). The investment is considered acceptable only when equivalent uniform annual benefit is greater than the equivalent uniform annual cost. From the compound interest table, (A / P, i = 12 %, n = 8 years) = 0.2013, (A / P, i = 12 %, n = 9 years) = 0.1877, (A / F, i = 12 %, n = 8 years) = 0.0813, (A / F, i = 12 %, n = 9 years) = 0.0677. Prove by calculations whether the investment above is acceptable.

1 Answers  


What is composition of 18/8 stainless steel?

1 Answers  


What are the different characteristics that can affect the flow of bulk solids and how?

0 Answers  


What's -74C, dew point is better the -70C dew point In draying unit .

1 Answers  


What are the assumptions made for kynch theory?

0 Answers  


Why an electromagnetic flow meter cannot be used for gases, steam and oil flow measurements?

1 Answers  


What is a "saltation velocity"?

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5085)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4452)
  • Electrical Engineering Interview Questions Electrical Engineering (16636)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)