Golgappa.net | Golgappa.org | BagIndia.net | BodyIndia.Com | CabIndia.net | CarsBikes.net | CarsBikes.org | CashIndia.net | ConsumerIndia.net | CookingIndia.net | DataIndia.net | DealIndia.net | EmailIndia.net | FirstTablet.com | FirstTourist.com | ForsaleIndia.net | IndiaBody.Com | IndiaCab.net | IndiaCash.net | IndiaModel.net | KidForum.net | OfficeIndia.net | PaysIndia.com | RestaurantIndia.net | RestaurantsIndia.net | SaleForum.net | SellForum.net | SoldIndia.com | StarIndia.net | TomatoCab.com | TomatoCabs.com | TownIndia.com
Interested to Buy Any Domain ? << Click Here >> for more details...


We are preparing another project which involves
Waste heat recovery from a 1 MW GE Engine.

The Engine in particular gives out flue gas at 487Deg C
with a flow rate of 5650 kg/hour and this can be cooled to
180 Deg C. This gives a thermal output of ~ 594 KW that is
available for input to VAM via heat exchanger / boiler.

Additionally 581 KW will be available from engine jacket
water (temperature profile 80/ 80 Deg C and a flow rate of
50m3/hr)

Our estimation is that 300 TR of cooling is possible with a
suitable VAM machine(s).
Please advise what is the most suitable arrangement with
maximum TR and min Capital expenditure.
plz reply me as early as possible


No Answer is Posted For this Question
Be the First to Post Answer

Post New Answer

More Electrical Engineering Interview Questions

why swinburnes test cannot be performed on series machines?explain

0 Answers  


hot water tank,top element 240v across,the bottom 120v across,why?

1 Answers  


What is potientiometer.What is the use of it.

1 Answers  


What is K-rated transformer? What is the use of it? What can be the size(pls provide calculation if possible) of K- factor transformer for 550kW,690V motor operating with drive (VFD)?

0 Answers  


while calculating the power absorbed by a resistor connected to the output of a half wave rectifier circuit should we use rms or average current? explain with reason.

1 Answers   Vedanta,


In synchronous motor, how the field current is related to armature current..i know its inversely proportional..but concept wise...i was nt clear....pls help me...

0 Answers   Siemens,


What is the difference between eath fault protection & Restricted Earth fault Protection?

2 Answers  


What is done to avoid interference of high frequency transmission lines with communication lines??

4 Answers  


what is the per unit cost of generation of electricity at thermal,hydro,desael,solar,gas power plant

1 Answers  


electrical ques

0 Answers  


what is the difference between surge arrestor and lightning arrestor ?

6 Answers  


how work the lighting arrestor?

2 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5086)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4453)
  • Electrical Engineering Interview Questions Electrical Engineering (16638)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1095)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)