Answer / vaibhav c

humidity

Answer / anil

i feel Fine dust particles in humidity majorly form Fog

what happen for input voltage output voltage input current output current and kva if we increase primery winding in transformer?

1 Answers  

---

2. A current i=(10+10 sin t)amperes is passed through MI type ammeter. its reading will be.........

0 Answers   SSC,

---

Whats the principle of lightning? How protection against lightning is achieved? Types of protection? How to select the height of lightning spike? as per the area.

4 Answers   HAL,

---

As all us know that the capacitor panel is connected to improve the power factor when it is PF is low. whether we can connect the capacitor panel on D.G. side(? If it is yes means why?

1 Answers   Aricent, Essar,

---

Actually why the transformers ate rated in KVA.?

2 Answers   Torrent Pharma, XYZ,

---

what is main parts of alternator.

3 Answers   HP,

---

How to select transmission line type (i.e. 11kv or 33kv) for new established industries

0 Answers  

---

explain harmonics in simple words..........

3 Answers   HMT,

---

DEFINE BREAKING CAPACITY OF BUSBAR & HOW IT IS CALCULATED?

0 Answers  

---

WHaT IS THE CONCEPT OF INDUCTION LAMPS IN MODERN LIGHTINGS, and HOW IT WORKS TO EMIT LIGHT ( AS NO ELECTRODES ARE PRESENT ) ?" COULD INDUCTION LAMPS CAUSE INTERFERENCE WITH COMUNICATIONS INTO A STORE USING INDUCTION LIGHTING ? WHAT IS THE BENEFIT OF USING THE LOW FREQENCY INDUCTION LAMP , VERSUS LED , AND VERSUS FLUORESCENT, AND VERSUS ANOTHER KIND OF LIGHTING . THANK yOU MOISES GUINDI

0 Answers  

---

what relation between transmission line & communication line?

1 Answers   NTPC,

---

Energy metering: On the property I am renting, the supply voltage is 2 x 110 volts. These 2 x phases enter a energy meter which then exit the meter to over head lines to my house. Question 1. The meter is single phase 240 volts but is being used as 2 x phase(2 x 110volt), is this acceptable? if not, please give me the reasons. The meter details are as follows: 60Hz 15amp Imax 100 amp Kd 3,6 Wh/R 1 fase 3 hilos Model FX 231. I think it was manufactured in Brasil From this meter, the cables run along over head aluminum conductors,I estimate the cross sectional area to be 25mm diameter, but the neutral is only about 10mm square diameter, which cover a distance of 170 meters and then terminate with an underground cable of 65 meter length, total length = 235 meters. There must be a huge voltage drop over this length. This line is protected with 2 x 200 amp aluminum fuses after the meter, there is no main switch in the distribution board. These 2 phases connect directly onto 2 busbars. Surely the neutral should be the same size as the conductors if not more? Question2. What are your thoughts about this installation, should there be better protection, is the neutral too small? During the night, the lights dim then brighten all the time, this cannot be good for my electrical appliances. In my home, I only have a small electric geyser and fridge, my stove works off gas. But when i use other appliances like the washing machine or microwave oven, the light dim. The internal wiring of this house is done with solid hard drawn copper wires and of course, they have to be under rated. I am a retired electrician by trade, but not on the metering and over head mains side, my experience is on the factory maintenance side of things. Your expertise on these matters will be greatly appreciated. Please inform me how to rectify or make any improvements Kind regards, my power bill is very expensive, so I need to know how to bring it lower. Kind regards, Brian

1 Answers  

---