which connection is safer series or parallel?usually which
connection we prefer at home?
- 5 Answers
- 8328 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / k mohana krishna
parallel connection is the best connection in my opinion.
because in series one of the bulb get fused off the total house supply fail, where as in parallel only that bulb will effect.
| Is This Answer Correct ? | 17 Yes | 0 No |
Answer / p.gupta.1852
Both connection are harmfull if not worked safely. You may
ask that which one is very usefull and why. Usefullness
of the connections is depends on your requirement and
availability and type of supply source .
In series connection source voltage will divide in the
loads connected in series and current will depends on sum
of impedance of the loads.In series connections if any load
is defective the other load can not be operated.Also if
different loads of current levels are connected in series
they will not give required result.
In parallel connections source voltage will be same for all
loads upto the voltage regulation level and current will
depend on sum of current of each load. As number of loads
increases current will also increase.If any one load became
defective other loads will do there work normally.
Parallel connections are required in house wiring because
our appliances are of same voltage level and are of
different current level and we want them to operate
saperatly.
| Is This Answer Correct ? | 5 Yes | 0 No |
Parallel or Series connection, all depends upon the
requirement. In Homes, parallel connection is preferred
because the apparatus used in home is of same voltage level
like AC, Iron, Microwave, Tubes, Bulb etc. all the equipment
marked 220v Rating. whereas series connection is used where
Low voltage devices are connected to sum up to connected to
equal supply voltage.
Both are equally safe and harmful.
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / karthik
Parallel connection is good with compare to series connection.
because,
in series connection the current will divide & in parallel
voltage will divide.
Dont ask this type of silly questions ok bye.
| Is This Answer Correct ? | 1 Yes | 18 No |
c++ write a program to use a fuction call "max"which accepts an intger arrey of size5.as an arrument and return the larger and smallest of the arrey to main without changing. the original changing of the original position of the element of the arrey.
Why is the earth socket in an electrical plug outlet made thicker and lenghty?
what is diffrence between neutral and earth wire
23 Answers Bhel, Esab, MTNL,
Write a note on RC operational amplifier as integrator
If one ct is reversely connected in Y system what will effect in kwh and kvarh meter?
why we use Test Terminal Block in 11 KV and 33 KV electrical panels.
WHY HVDC?
what is the difference between electrical degree n mechanical degree?
What are dcs and plc?
why 1.7Uo for HV cable Hi pot test?IE standard why?
When a single pase capacitor run motor- run on 230vac and Case(1)run with 8 Mfd 250 vac.capacitor , Case( 2) run with 8 Mfd 400vac capacitor. What is difference between both case regarding power ,efficiency etc?
SMPS (Switch Mode Power Supply) unit is denoted by KW or KVA?
-
Civil Engineering (5085) - Mechanical Engineering (4451)
- Electrical Engineering (16632)
- Electronics Communications (3918)
- Chemical Engineering (1095)
- Aeronautical Engineering (239)
- Bio Engineering (96)
- Metallurgy (361)
- Industrial Engineering (259)
- Instrumentation (3014)
- Automobile Engineering (332)
- Mechatronics Engineering (97)
- Marine Engineering (124)
- Power Plant Engineering (172)
- Textile Engineering (575)
- Production Engineering (25)
- Satellite Systems Engineering (106)
- Engineering AllOther (1379)
