Interested to Buy Any Domain ? << Click Here >> for more details...
How can you measure out exactly 4 litres of water from a tap
using a 3 litre and a 5 litre bucket?
- 7 Answers
- 17091 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / durga
first fill the 5lt bucket, then pour this water into 3lt
bucket.. then we have 2lts of water in 5lts bucket.then
empty the 3lts bucket, again fill with 2lts of water which
is in 5lts bucket. now we have 2lts of water in 3lts bucket.
now again fill the 5lts bucket, then pour this water in to
3lts bucket up to complete..i.e it takes one lt water. now
we have 4 lts of water in 5lts bucket.
| Is This Answer Correct ? | 58 Yes | 7 No |
Answer / :)
first put empty 5 ltr bucket than use 3 ltr bucket to fill
it with 3 ltr water now 5 ltr bucket has 3 ltr water in it.
now again fill 3 ltr bucket from water and pour reamining 5
ltr again... now 5 ltr bucket is full with water. and 3 ltr
bucket has 1 ltr left in to it. now do empty the 5 ltr
bucket by throwing water. now u have 5 ltr bucket empty now
pour water of 3 ltr letf above i.e one litre in to 5 ltr
bucket.. now we have one litre water in 5 ltr bucket.. fill
3 ltr bucket again and pour full water of it i.e 3 ltr in to
5 ltr bucket now 5 ltr bucket has 4 ltr water in it.. simple
| Is This Answer Correct ? | 9 Yes | 0 No |
Answer / anonymous!!
Fil the 3 l bucket, pour it into the 5l, (so 3l in 5;) fill
the 3l again pour it into the 5l til the brim. so 5 l
full .. 3l bucket wil have 1 l in it... pour out the water
in the 5l bucket.. pour in the 1l(in the 3l) n fil 3l
bucket again n pour it into the 5l.. =4l!
| Is This Answer Correct ? | 8 Yes | 1 No |
Answer / linilbabu
(4 litres of water from a tap)-
(using a 3 litre) + 5 litre bucket=total measuring out(6
litre)
(4 litres of water from a tap)-
(using a 5 litre) + 3 litre bucket=total measuring out
| Is This Answer Correct ? | 1 Yes | 3 No |
For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet interface? A.) novell-ether B.) gns C.) snap D.) arpa E.) sap F.) dix
hello i am new to this, i need to know how will i complete a basic scenario that ask the required number of networks that is 80 and the minimum number of host that is 3000 and the network address is 10.0.0.0 and i need to need how to compute to get the answer on what is the subnet mask.
Identify the command to display all the valid commands at the given mode? A.) Help all B.) Help C.) All commands D.) ?
Identify the 3 pieces of hardware you would not install to prevent broadcasts? A.) Switch B.) Repeater C.) Bridge D.) Router
What is the regional Telco office called, where the customers local loop terminates? A.) Demarc B.) DTE C.) DCE D.) CO E.) CPE
Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. Which of the following statements is false? If your Frame Relay link does not support inverse ARP, you must manually map DLCIs to network Address. One of the major advantages of Frame Relay is its ability to connect to multiple PVCs using only one physical link. DLCI addresses are determined by the network administrator when installing the network. In order for two ends of virtual circuits to communicate using Frame Relay, their network addresses must be mapped to DLCIs.
What are segments?
what is ip address?
When a Distance Vector routing protocol detects that a connected network has gone down, it sends out a special routing update packet, telling all directly connected routers that the distance to the dead network is infinity. This is an example of which routing technology? A.) ICMP. B.) Only Link State routing protocols have this intelligence. C.) Triggered updates. D.) Garrison-4. E.) Split Horizon. F.) Poison Reverse.
what is uplink port why are we use this port,this port having extra feature or only use to redundant link or other please explain it ,,,,,,,,,,,,,,,, bcz i am very confuse ..... Thanks
What is the first step in data encapsulation? A.) User information is converted into data. B.) Frames are put into bits. C.) Data is converted into segments. D.) Segments are converted into datagrams and packets. E.) Packets are put into logical frame.
How do we do encryption and authentication in L2TP?
CCNA 
