Interested to Buy Any Domain ? << Click Here >> for more details...
For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet
interface?
A.) novell-ether
B.) gns
C.) snap
D.) arpa
E.) sap
F.) dix
- 1 Answers
- 4072 Views
- I also Faced
- E-Mail Answers
Explain the types of ospf configuration?
what is unike ip address
Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload
Why Clock rate command is not configured on ethernet interface of a router?
What is a function of a reliable transport layer connection? A. route selection B. acknowledgements C. session checkpoints D. system authentication
Identify the IPX standard access-list number range? A.) 600 - 699 B.) 1000 - 1099 C.) 1 - 99 D.) 100 - 199 E.) 800 - 899
Which OSI layer handles physical addresses and network topology? A.) Presentation B.) Physical C.) Transport D.) Application E.) Data-Link F.) Network
The Datalink Layer is broken down into 2 layers, LLC and MAC. The LLC establishes media independence and what else? A.) Provides Windowing. B.) Provides flow control. C.) Provides SAP's (Service Access Points). D.) The Datalink layer does not have sublayers. E.) Provides SAP's (Service Advertising Protocol). F.) RIP Updates.
GUY i Have attended one interview for the data craft and they are offering me L1 postion and i am working at l2 in cisco so there is no way to get in the datacraft i am posting here the question he asked to and i have tested the interviewer and i come to know he was not having any knowledge. His questions are-: 1) what is Vlan 2) what is stp and what is difference between stp and RSTP 3) what is HSRP and Diffrence betwwen HSRP and GLBP 4) how to configure HSRP 5) Scenario Based question ( if we have two router and both are connected and there are having redundancy means two interface of the router r1 is connected to the two interface of Router R2 (R1)-------------(R2 (R1)-------------(R2 Now he want to configure the router in such a Manner that if one link down second link should come up.My answer was HSRP and his is "F looting static routing was i wrong "i know F looting Static routing is Theoretically possible but it is not fusible in the scenario where you have multiple router connected to the same router and if you have configured sub interface i challenged him and he lost The Battle and he get angary 5) what the eigrp and how it works 6) tables in eigrp 7) the information of feasible successor where it saved now after answering these all he was very angry ( i can fill the heat) 8) then he come to ospf Area type ( he was also not aware) 9) LSA type and its working ( he was also having confusion ) 10) then is asked routing by rummer( Theroy) 11) hello and dead intervel of EIGRp (theory) 12) Selection cretaria for Eigrp slecting best path ( here we have a long discussion on MTU and he lost the battle and agree That MTU never comes in the accounts in this process) 13) what is ACL type of acl ( here he was aware of TWO type Standard and extended i have told him 5 type( he again get Angry) We have 2hr of discussion and and he told me he will call me latter but i know he never call
What does the term "attenuation" mean in data communication? 1 loss of signal strength as distance increases 2 time for a signal to reach its destination 3 leakage of signals from one cable pair to another 4 strengthening of a signal by a networking device
What do the following commands accomplish? access-list 1 deny 172.16.4.0 0.0.0.255 access-list 1 permit any interface ethernet 0 IP access-group 1 out A. This will block traffic from subnet 172.16.4.0 and allow all other traffic. B. This will allow traffic from subnet 172.16.4.0 and block all other traffic. C. All traffic is allowed. D. All traffic is blocked.
Repeaters work at which layer of the OSI model? A.) Network B.) Session C.) Transport D.) Physical
CCNA 
