What does the ping response & mean?
* A: unreachable
* B: congestion
* C: user interrupt
* D: unknown packet type
* E: lifetime exceeded
- 6 Answers
- 19758 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / sid
What does the ping response ? mean?
A: unreachable
B: congestion
C: user interrupt
D: unknown packet type
E: lifetime exceeded
Correct Answer: D >unknown packet type (verified)
| Is This Answer Correct ? | 3 Yes | 0 No |
Answer / sid
What does the ping response ? mean?
A: unreachable
B: congestion
C: user interrupt
D: unknown packet type
E: lifetime exceeded
Correct Answer: D
Cisco PING Response Codes
Response Meaning
! (exclamation mark) Success
. (period) Timed out waiting for reply
U Destination unreachable
| (vertical bar) Ping process interrupted
? (question mark) Unknown packet type
C Congestion-experienced
& (ampersand) Time to live exceeded
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / ekta
E: lifetime exceeded
. = network server timed out
U = destination unreachable
Q = source quench (destination too busy)
M = could not fragment
? = unknown packet type
& = packet lifetime exceeded
| Is This Answer Correct ? | 0 Yes | 0 No |
What are two ways IPX supports multiple logical networks on an individual underrate? (Choose two) A. network number B. routing protocol C. encapsulation type D. autonomous system number
Identify 2 HDLC characteristics? A.) Default serial encapsulation B.) Open standard C.) Supports Stacker compression D.) Supports point-to-point and multipoint
Identify the OSI layer associated with bits? A.) Physical B.) Network C.) Binary D.) Data link
What is mtu and what is its size for transmission?
LAN stands for which of the following? A.) Local Area Network B.) Local Arena Network C.) Local Area News D.) Logical Area Network
I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
Identify the correct pair of Novell Ethernet encapsulation and Cisco terminology? A.) Ethernet II, Snap B.) Ethernet 802.3, Novell-Ether C.) Ethernet SNAP, Arpa D.) Ethernet 802.2, Snap
What is the total bandwidth of all channels on a BRI circuit? A. 56 kps B. 64 kps C. 112 kps D. 128 kps E. 144. kps
Inverse ARP serves what purpose? A.) Method for a local router to introduce itself to the remote end of the connection B.) Broadcast a routing table update C.) Identify MAC addresses if the IP address is known D.) Sent every 10 seconds used to verify the Frame Switch is still active
Identify the command to display the IP routing table? A.) show route B.) show ip route C.) show ip table route D.) show ipx route
Which network mask should you place on a Class C address to accommodate a user requirement of two subnetworks with a maxximum of 35 hosts on each networks A. 255.255.255.192 B. 255.255.255.224 C. 255.255.255.240 D. 255.255.255.248
Choose the following that are benefits to segmenting with router: A.) Flow Control B.) Manageability C.) Multiple Active Paths D.) Explicit packet lifetime control
CCNA 
