Answer / anil babu

BS2 is Bharath stage2 & BS3 is Bharath Stage3 these are
engine versions upgrading to reduce pollution

Answer / venkat

diffrence in its pump to reduce the air pollution

Answer / bhaskar mukherjee

BS2 is Bharath stage2 & BS3 is Bharath Stage3 these are
engine versions upgrading to reduce pollution

Answer / anup kumar

IN BS2 there is No catalytic converter to reduce formation
of co and HC whereas in BS3 catalytic converter is
available to reduce the formation of HC and CO. So less
emission of HC and co will take place in BS3

Answer / kasiviswanathan

On 2000 CMVR(Central Motor Vehicle Regulation Act) came
into existence on Year 2000.That Any car which is
manufactured in India will follow the Pollution Norms which
is called BS-1, BS-2,BS-3 & BS-4,etc...Every 3 Years, the
regulation to be followed in the State Captals mainly NCR
Areas. At present, New cars are selling in BS-4
Regulations.This will reduce Pollution and High Technology
is used to reduce Pollution.
Now, MPFI,GDI & CRDi Technologies came into existance in
India because of the Pollution Norms adopted by Ministry of
Transport thro CMVR 2000.
Any other doubts visit https://www.araiindia.com/

Answer / nicky

Bharat stage 2/3/4 are engine emission standard for 4 wheeler vehicle in India in reference of Euro2/3/4 norms.

Answer / purvesh

Bs 3 engines have reduced pollutants as compared to Bs3 in various cases of different loads asd speeds.

Answer / sandip bose

reduce pollution.various cases of different loads asd
speeds.

Answer / chinni

For 2-and 3-wheelers, Bharat Stage II (Euro 2) will be applicable from April 1, 2005 and Stage III (Euro 3) standards would come in force from April 1, 2010

Answer / kuldeep singh

a bs2 and bs3 engine changed only smoke value.bs2 engine
give smoke 30@3200rpm,55@2000 rpm& bs3engine give
15@3200rpm,30@2000rpm.means bss engine is best in favour of
bs2..

working the cam

3 Answers  

What is mean by VDi engine?

1 Answers   Maruti Udyog,

What is clutch drag?

0 Answers  

Mean effective radius of contact surfaces of a clutch plate is decided by a) Coefficient of friction b) Axial pressure c) Space available in the vehicle d) Amount of torque to be transmitted

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,

Why black colour are used for tyres? is there anything related with heat conduction?

0 Answers  

The number of arms provided to the Cross of the Hook's joint is a) 1 b) 2 c) 3 d) 4

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,

why do cars have smaller tyres and bikes bigger ?

4 Answers   Ford, Hero Honda,

in internal combtion engine, maximum efficiency is65%. than 35% losses. but why not decreased losses ? any reason behind this ?

1 Answers  

CRANK shaft to be fixed to the engine, ? (1) Perpendicular CAM shaft (2) Inclined to CAM shaft (3) Parallel to CAM shaft (4) None of the above

3 Answers  

The function of the final drive is to a) Provide a permanent speed reduction b) To turn the drive round through 90o c) To provide drive to the rear wheels d) all of the above

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,

If the given tractive effort curve and the total resistance curve does not intersect, then a) The vehicle will accelerate b) The vehicle will decelerate c) The vehicle will not be able to go at this gradient for the given gear d) None of the above

0 Answers   Backbone, Bosch, MAHINDRA, Uniparts Group,

How bhp is measured?

0 Answers