1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

When you cords an IP address on a place router which command
stale the IP processing on the interface?

A. ip enable

B. network ip-address

C. ip address ip-address subnet mask

D. the exit command from the enabled configuration

E. copy running-configuration to startup-configuration

Question Posted / guest

Answers were Sorted based on User's Feedback



When you cords an IP address on a place router which command stale the IP processing on the interfa..

Answer / guest

Answer: C

Is This Answer Correct ?    0 Yes 0 No

When you cords an IP address on a place router which command stale the IP processing on the interfa..

Answer / guest

ip address ip-address subnet mask

Is This Answer Correct ?    0 Yes 0 No

When you cords an IP address on a place router which command stale the IP processing on the interfa..

Answer / nilesh

cords

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

Which of the following are valid WAN terms? A.) DTE B.) DCE C.) Demarc D.) CPE

1 Answers  

What are the two primary operating modes for frame switching? A. Full Duplex B. Half-Duplex C. CSMA/CD D. Cut-through E. Fragmentation F. Store and Forward G. User mode H. Privileged mode

1 Answers  

What is link aggregration?? How many types of protocol are used on that???

3 Answers   Hathway,

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

2 Answers  




If i had 400 computers set in a site how many VLAN i should configure so that i can share a proper bandwith,and also i had two lease line connection of 2Mbps each,

1 Answers   IBM,

Difference between subnetting & Vlan??

7 Answers   Cisco, TCP,

What are the two types of transmission technology available in ccna?

1 Answers  

Briefly explain the conversion steps in data encapsulation.

0 Answers  

To monitor ipx traffic on a network, what command would you use? A. debug ipx transaction B. show ipx traffic C. show ipx events D. display ipx traffic

3 Answers  

Which of the following are examples of the Transport Layer? A.) Token Ring B.) UDP C.) TCP D.) IP E.) SQL F.) LLC

2 Answers  

Hi Gyes, here is new question. can you provide answer of following question Like linux, can we windows as router? If yes how can we able to do this,

2 Answers  

For more CCNA Interview Questions Click Here
Categories