An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel
- 1 Answers
- 4796 Views
- I also Faced
- E-Mail Answers
What are the IGRP stability features?
How many (minimum and maximum) ports are present in a router?
hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface
hi i have some difficulty plz reply as s0on as possible. 1 what is csma/cd(i know u are familer with that protocol) 2 what is the need for it and and 3 rd one in which i need help how to enable csma/cd at router or switches shain make it answer as sson as possibele and call me afetr reply thanks jitendera kuamr sinha
Which IP address and wildcard mask would you use in your ACL to block all the hosts in the subnet 192.168.16.43/28?
Identify 3 characteristics of ISDN? A.) Transports voice and data B.) Transports voice only C.) Support both BRI and PRI D.) Runs over existing phone lines E.) Same as X.25
Suppose we have 4 switches runing in VTP mode. So when i create a VLAN in Server Switch this VLAN info reflect in all other switch. So question is - A) Suppose i m practicing this scenario in BOSON software, When a create a VLAN in server switch n ADD ports of switch to that VLAN, the same number of ports of client switch also belongs to dat VLAN. For example - In switch A (Server mode), i create a VLAN 7 name Hyderabad & port number 1, 2 & 3 put into this VLAN. Another Switch B (Client mode), its also showing that port number 1,2 & 3 belong the same VLAN. How cud it possible... As we know, VTP share only VLAN configuration information. Cud anyone explain it please....!!!! B)Same thing, when i m practicing in PACKET TRACER 5.0, its only showing that VLAN configuration information is shared. No port information is shared at all. I can manually configure individual switch port to respective VLAN as our wish. Cud anyone explain it please..!!!
When discussing static routes, what is the gateway parameter used for? A.) Determining the dynamic route B.) Defining the subnet C.) Defining the Administrative Distance D.) Determining the next hop
How we ping ICMP a NIC with a correct IP address but with wrong MAC address Do all NIC's can run inpromiscuous mode
In IOS boot sequence if the flash is erased, and there is no access to TFTP server, and we can't load the partial IOS from ROM. Is there any possiblity that we can still boot the router/switch from external PC in which the IOS is installed?
Define Poison Reverse? A.) To prevent regular update messages from reinstating a route that has gone down B.) Packets sent out that are not destined for a network go to the default network C.) Information received on an interface cannot be sent back out the same interface D.) When a network goes down, that network is advertised with an infinite metric
Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.
CCNA 
