Which show underrate serial 1 status statement indicates
that the shutdown command was issued on that interface?
A. Serial 1 is up line protocol is up
B. Serial 1 is up line protocol is down
C. Serial 1 is down line protocol is down
D. Serial 1 is administratively down the line protocol is down
- 2 Answers
- 4240 Views
- Pioneer Labs, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / kunal
D. is appropriate answer.
when no shut is nt defined in interface then serial 1 will
show adminsitratively down and protocol also down
if clock rate nt given in any interface then answer will be
B.
if both indicates in down status it means there is problm
in LAN.
both are up means clock rate and no shut command properly
used.
| Is This Answer Correct ? | 2 Yes | 0 No |
What is a switch and why we are using switches?
from last ten days i watched that no any new questions are placed in ccna catogarey.so plz place the questions it is very use full to beginers like us
As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.
how to shutdown a Cisco router from command prompt?
11 Answers Atlas Systems, HCL,
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain
Identify the following components of the IPX address 2e.0000.0065.ed43 A.) Not a valid IPX address B.) Network = 2e, Subnet = 0000, Node = 0065.ed43 C.) Network = 2e.0000, Node = 0065.ed43 D.) Network = 2e, Node = 0000.0065.ed43
What is STP and what is the difference between PVST and RSTP
Layer 1 and Layer 2 devices must forward a broadcast. Which of the following devices fall into this category? Gateway Switch Router All of the above.
The Datalink Layer is broken down into 2 layers, LLC and MAC. The LLC establishes media independence and what else? A.) Provides Windowing. B.) Provides flow control. C.) Provides SAP's (Service Access Points). D.) The Datalink layer does not have sublayers. E.) Provides SAP's (Service Advertising Protocol). F.) RIP Updates.
Which of the follwing are true of standard half-duplex Ethernet circuitry? A. It is alternate one-way communication B. The receive (RX) is wired directly to the transmit (TX) of the remote station C. The transmit (TX) is wired directly to the receive (RX) of the remote station D. Collisions are not possible E. Both stations can transmit simultaneously
The following is partial output from a routing table, identify the 2 numbers in the square brackets; '192.168.10.0 [100/1300] via 10.1.0.1, 00:00:23, Ethernet1' A.) 100 = metric, 1300 = administrative distance B.) 100 = administrative distance, 1300 = hop count C.) 100 = administrative distance, 1300 = metric D.) 100 = hop count, 1300 = metric
Identify the effect of Ctrl-Z? A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the ping operation D.) Exits privileged exec mode
CCNA 
