What do you use the Aux port for?
A.) Console
B.) Terminal editing
C.) Modem
D.) Backup logging
- 1 Answers
- 3820 Views
- I also Faced
- E-Mail Answers
hi shyam i am putting urs question here I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0
Write out a config to permit only the below MAC address to pass traffic through a port on your switch. in another way writhe a confrigation which permit only mac address trfaic through a port of your switch
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
Which OSI layer supports the communication component of an application? A.) Data-Link B.) Physical C.) Session D.) Presentation E.) Application F.) Transport
Which layer is responsible for putting 1s and 0s into a logical group? A.) Session B.) Application C.) Transport D.) Data Link E.) Physical F.) Network
Identify the command that forces the router to load into ROM mode upon a reload? A.) boot system rom B.) rom boot C.) boot system flash rom D.) boot router rom
Identify 3 IP applications? A.) AURP B.) ARP C.) Telnet D.) SMTP E.) DNS F.) RARP
What does -1 mean in an extended IPX access-list? A.) Any IP address B.) Deny all C.) Deny host D.) Any host or any network
What information can you get from CDP info: (choose all that apply) A.) Hardware platform B.) One address per protocol C.) Software platform D.) Hostname E.) The same info as show version F.) Incoming/outgoing port
Which feature should a routing protocol have to support vlsm?
CCNA 
