Answer / gns

firstely go through basic of initial subject like fm ,ht ,mt
then cre etc try to understnd it practically concept
link all subject togetherly and to use all concept in
project work , seminar design subject.
try to solve technical objective by applying basics because
objective requiued more and more basic knowledge the go to
next step of detail study of each subject in course.

Answer / sudansu

Think pratically what r u study,means imagine the
problems.so www.unitoperation.com,wikipedia,chempeople site
r thre .

Answer / v.m.desai b.e chemical

APPLY YOUR KNOWLEGE PRACTICALLY AND IMPROVE THE PRACTICAL
KNOWLEDGE

ENGINEERING ECONOMY - EXAMPLE 7.2 : In the purchase of a machine with a period n = 8.5 years, the minimum attractive rate of return, i = 12 %, the cost P = $55000, F = $4000 is the salvage, annual maintenance A = $3500. The return of the investment or equivalent uniform annual benefit is $15000. The equivalent uniform annual cost is P (A / P, i, n) + A - F (A / F, i, n). The investment is considered acceptable only when equivalent uniform annual benefit is greater than the equivalent uniform annual cost. From the compound interest table, (A / P, i = 12 %, n = 8 years) = 0.2013, (A / P, i = 12 %, n = 9 years) = 0.1877, (A / F, i = 12 %, n = 8 years) = 0.0813, (A / F, i = 12 %, n = 9 years) = 0.0677. Prove by calculations whether the investment above is acceptable.

1 Answers  

---

Explain the reasons of removal of particles from effluent gas?

0 Answers  

---

In gas and water who's density is greater and why?

5 Answers  

---

How can you quickly estimate the horsepower of a pump?

0 Answers  

---

What are the effects of oils on the properties of Polyolefins?

0 Answers   IOCL,

---

what is the PH value for boiler water.

12 Answers  

---

MY generator water cooler inlet line height - 11 mtr inlet water line height - 7 mtr water come into the line from overhead tank, O/H tank height - 20 mtr the first tapping in the inlet line is 2" line which down to 4 mtr level plateform., second tapping in inlet water line goes to a pump 6" line installed at 4 mtr level plateform, pump capacity 200m3/hr, head- 30 mtr, hp-40. the outlet of pump of 6" water line connected to a header of 6 mtr long of 6" line, on this header the six tapping are connected, 4 nos. 3" line goes to 11 mtr height water cooler the pressure of the line is 0.15 to 0.25 kg/cm2, 2" and 4" pipe line connected to a cooler at 4 mtrlevel plateform. my question is, at 11 mtr height level the quantity of water and flow is not sufficient for my cooler, the temp. of cooler is rises much more. you are requested to suggest the modification of pipe line/ pump for take more water flow and pressure (desired pressure is 1 kg/cm2)

0 Answers   Simbhaoli Sugars,

---

which chemical reaction has the maximum evolution of heat?

3 Answers   IOCL,

---

THERMODYNAMIC - EXAMPLE 10.1 : The water is superheated steam at 440 degree Celsius and 17.32 megapascals. Estimate the enthalpy of the steam above. From the steam table for water at 440 degree Celsius, enthalpy of steam, h at 18 megapascals is 3103.7 kilojoules per kilogram and at 16 megapascal is 3062.8 kilojoules per kilogram. Assume that h = mP + c where P is pressure; m and c are constants at fixed temperature with small differences in P.

1 Answers  

---

Explain what type of pump may be appropriate for a liquid near saturation, a low flow rate, and very limited npsha (net positive suction head available)?

0 Answers  

---

Is there a rule of thumb to estimate the footprint of a cooling tower during design phase?

0 Answers  

---

CHEMICAL ENERGY BALANCE - EXAMPLE 11.2 : Calculate the cooling duty, H required to condense and cool acetone from 100 degree Celsius to 25 degree Celsius at atmospheric pressure. The heat of vaporization for acetone at its normal boiling point is 30.2 kJ / mol. The boiling point of acetone at atmospheric pressure is 56 degree Celsius. The flowrate of acetone through the condenser is 100 mol / s = N. Value of sensible heat needed to increase the temperature of acetone in liquid form from 25 to 56 degree Celsius is 4.06 kJ / mol. Value of sensible heat needed to increase the temperature of acetone in vapor form from 56 to 100 degree Celsius is 3.82 kJ / mol. Unit of H is kJ / s.

1 Answers  

---